Hi,
I am uising Suse linux on my system and i tried :
man ethtool and i got the manual for ethtool but when i tried to use the command as:
ethtool -a eth0
it says Command not found.
also, i tried rpm -qa|grep ethtool i got:
ethtool-3-15.2 so,it means my system has ethtool server or... (4 Replies)
Hi,
I'm using ethtool to change network settings:
Just for the experiment, i want to change speed to 10, instead of 100,
I type:
ethtool -s eth0 speed 10 duplex full autoneg off
and to view settings i type:
ethtool eth0, and get this:
Settings for eth0:
Supported ports:
... (4 Replies)
Hello, I've got a FreeBSD 6 server running on my network that I used as a file server for my main computer. However I've really become frustrated with the slow up/down speeds I'm getting, about 100KB/s, which is about as bad as if I was using a "real" server. My setup is as follows:
ISP
|... (4 Replies)
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Hi,
I have a script that, basically, has two input files of this type:
file1
key1=value1_1_1
key2=value1_2_1
key4=value1_4_1
...
file2
key2=value2_2_1
key2=value2_2_2
key3=value2_3_1
key4=value2_4_1
...
My files are 10k lines big each (approx).
The keys are strings that don't... (7 Replies)
Hi, there is an incompatibility between my NIC and my Western Digital Powerline adapters which appears to cause autonegotiation to fail intermittently, most often following a reboot. Running the following Ethtool script will establish a connection immediately:
#!/bin/sh
# chkconfig: 345 85... (12 Replies)
Hello all. I have VSFTP up and ruining on ubuntu 10.04. It works great inside LAN, however when it comes to using it outside i have some problems. If i try to connect from filezila i get the listing and if i try to download it shows it will take forever to receive a file which is larger then 1mb,... (2 Replies)
Hi All,
I am trying to find my NIC card speed in centos 5. But i am unable to get the info using ethtool command.
# ethtool eth0
Settings for eth0:
Link detected: yes
and even tried to look for the file # cd /sys/class/net/eth0/speed files which is also not available.... (8 Replies)
Discussion started by: sravani25
8 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)