Hi,
I need to get the user input and execute a particular script based on the input provided.
For E.g. When I execute the script say Test.sh it should prompt "For which country I need to execute the script? (US/India)"
Based on the input as US or India from the user the execution of... (8 Replies)
I am using festival speech synthesis system and I would like to allow user input in a browser. This will be taken by a php page which is then supposed to pass the input text to a perl script. The perl script should pass this text to the festival engine by executing a unix command. this in turn... (2 Replies)
Hi,
I have a perl script which prints me the epoch value of a specific date and time given.Now I want to proceed to a next step ie i want to give the input at the time of execution.
I have to initialise the date and time values in the script before executing it.But now i want to give the date... (3 Replies)
Hello
I am trying to create a user input shell scipt. The objective is user should enter the circuit number and the input is saved in a log file. If the user does not enter anything then the question should prompt it until the circuit no. is entered.
Can any one please correct the code below.... (3 Replies)
Hi Jim,
I have following script,i which i need to take dynamic value .
script,
nawk -v v1=grep"INT_EUR" $propertifilename | cut -d"=" -F2` -F'~' '{if (NF-1 !=v1)
{print "Error in " $0 " at line number "NR" tilde count " N-1}}' $filename
In the above script i want to use INT_EUR as a variable... (2 Replies)
Hi gurus,
I have a requirement where I need to remotely run a perl script as another user.
Running the script locally as the required user is fine, however I need to su with the script due to filesystem permission issues. I do not want to update permissions on the remote server due to security... (5 Replies)
i have a script which takes input from user, if user gives either Y/y then it should continue, else it should quit by displaying user cancelled.
#!/bin/sh
echo " Enter your choice to continue y/Y OR n/N to quit "
read A
if
then
echo " user requested to continue "
##some commands... (7 Replies)
#/bin/sh
echo "enter the user name"
read $username
echo "Enter new home directory"
read $newhd
usermod -d $newhd $username ;;
error while executing :
enter the user name
Rev
Enter new home directory:
/home/58745
usermod: option requires an argument -- 'd'
Try `usermod --help' or... (2 Replies)
Using Linux (bash), I have two files which contain information about berries. Example:
file1.txt:
Blueberry blue 14
Raspberry red 12
Blackberry dark 4
file2.txt
Blackberry sour 4 3
Blueberry tasty 12 78
Strawberry yummy 33 88
I want to merge these two files into one. The desired... (5 Replies)
Hi everyone, I'm new here and just a beginner in linux scripting.
Just want to ask for help on this one.
I am trying to create a script that will accept user input (year-month and user/s).
I wanted to have the script to continue running, until the user inputs a DATE and name/s of user/s. ... (2 Replies)
Discussion started by: Helskadi
2 Replies
LEARN ABOUT CENTOS
trace-cmd-split
TRACE-CMD-SPLIT(1)TRACE-CMD-SPLIT(1)NAME
trace-cmd-split - split a trace.dat file into smaller files
SYNOPSIS
trace-cmd split [OPTIONS] [start-time [end-time]]
DESCRIPTION
The trace-cmd(1) split is used to break up a trace.dat into small files. The start-time specifies where the new file will start at. Using
trace-cmd-report(1) and copying the time stamp given at a particular event, can be used as input for either start-time or end-time. The
split will stop creating files when it reaches an event after end-time. If only the end-time is needed, use 0.0 as the start-time.
If start-time is left out, then the split will start at the beginning of the file. If end-time is left out, then split will continue to the
end unless it meets one of the requirements specified by the options.
OPTIONS -i file
If this option is not specified, then the split command will look for the file named trace.dat. This options will allow the reading of
another file other than trace.dat.
-o file
By default, the split command will use the input file name as a basis of where to write the split files. The output file will be the
input file with an attached '.#' to the end: trace.dat.1, trace.dat.2, etc.
This option will change the name of the base file used.
-o file will create file.1, file.2, etc.
-s seconds
This specifies how many seconds should be recorded before the new file should stop.
-m milliseconds
This specifies how many milliseconds should be recorded before the new file should stop.
-u microseconds
This specifies how many microseconds should be recorded before the new file should stop.
-e events
This specifies how many events should be recorded before the new file should stop.
-p pages
This specifies the number of pages that should be recorded before the new file should stop.
Note: only one of *-p*, *-e*, *-u*, *-m*, *-s* may be specified at a time.
If *-p* is specified, then *-c* is automatically set.
-r
This option causes the break up to repeat until end-time is reached (or end of the input if end-time is not specified).
trace-cmd split -r -e 10000
This will break up trace.dat into several smaller files, each with at most
10,000 events in it.
-c
This option causes the above break up to be per CPU.
trace-cmd split -c -p 10
This will create a file that has 10 pages per each CPU from the input.
SEE ALSO trace-cmd(1), trace-cmd-record(1), trace-cmd-report(1), trace-cmd-start(1), trace-cmd-stop(1), trace-cmd-extract(1), trace-cmd-reset(1),
trace-cmd-list(1), trace-cmd-listen(1)AUTHOR
Written by Steven Rostedt, <rostedt@goodmis.org[1]>
RESOURCES
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/trace-cmd.git
COPYING
Copyright (C) 2010 Red Hat, Inc. Free use of this software is granted under the terms of the GNU Public License (GPL).
NOTES
1. rostedt@goodmis.org
mailto:rostedt@goodmis.org
06/11/2014 TRACE-CMD-SPLIT(1)