03-05-2020
On aggr0 you can only define IP address from native VLAN on those ports.
If you wish to define a tagged IP on the hypervisor, you need to create vlan interface, then define IP on that.
If you wish to use the interface for virtual machines, you define a VSW with aggr0 link.
Then you add a vnet via ldm command using that VSW.
You can have both on the hypervisor, vlan interfaces and VSW above aggr0, but of course with different IP addresses (vm and hypervisor).
I would recommend reading about Oracle VM server for SPARC and a bit about networking as well
Looks like you are mixing hypervisor and vm part regarding network.
Regards
Peasant.
These 2 Users Gave Thanks to Peasant For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
6. Solaris
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies
7. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
8. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
9. Solaris
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
CHCPU(8) System Administration CHCPU(8)
NAME
chcpu - configure CPUs
SYNOPSIS
chcpu -c|-d|-e|-g cpu-list
chcpu -p mode
chcpu -r|-h|-V
DESCRIPTION
chcpu can modify the state of CPUs. It can enable or disable CPUs, scan for new CPUs, change the CPU dispatching mode of the underlying
hypervisor, and request CPUs from the hypervisor (configure) or return CPUs to the hypervisor (deconfigure).
Some options have a cpu-list argument. Use this argument to specify a comma-separated list of CPUs. The list can contain individual CPU
addresses or ranges of addresses. For example, 0,5,7,9-11 makes the command applicable to the CPUs with the addresses 0, 5, 7, 9, 10, and
11.
OPTIONS
-c, --configure cpu-list
Configure the specified CPUs. Configuring a CPU means that the hypervisor takes a CPU from the CPU pool and assigns it to the vir-
tual hardware on which your kernel runs.
-d, --disable cpu-list
Disable the specified CPUs. Disabling a CPU means that the kernel sets it offline.
-e, --enable cpu-list
Enable the specified CPUs. Enabling a CPU means that the kernel sets it online. A CPU must be configured, see -c, before it can be
enabled.
-g, --deconfigure cpu-list
Deconfigure the specified CPUs. Deconfiguring a CPU means that the hypervisor removes the CPU from the virtual hardware on which
the Linux instance runs and returns it to the CPU pool. A CPU must be offline, see -d, before it can be deconfigured.
-p, --dispatch mode
Set the CPU dispatching mode (polarization). This option has an effect only if your hardware architecture and hypervisor support
CPU polarization. Available modes are:
horizontal The workload is spread across all available CPUs.
vertical The workload is concentrated on few CPUs.
-r, --rescan
Trigger a rescan of CPUs. After a rescan, the Linux kernel recognizes the new CPUs. Use this option on systems that do not auto-
matically detect newly attached CPUs.
-V, --version
Display version information and exit.
-h, --help
Display help text and exit.
RETURN CODES
chcpu has the following return codes:
0 success
1 failure
64 partial success
AUTHOR
Heiko Carstens <heiko.carstens@de.ibm.com>
COPYRIGHT
Copyright IBM Corp. 2011
SEE ALSO
lscpu(1)
AVAILABILITY
The chcpu command is part of the util-linux package and is available from Linux Kernel Archive <https://www.kernel.org/pub/linux/utils
/util-linux/>.
util-linux July 2014 CHCPU(8)