Solaris 11 link aggregation - not working - can't ping gateway
This link was helpful and I got the idea that vlanNUM would be created on OVM/hypervisor level.
I deleted VLAN interfaces, recreated aggr0 with net0 and net7. But I can't ping its gateway. I can see packets incoming from two VLANs, if I snoop on net0, net7 and aggr0.
Per network guys, their side configurations are okay, but I will check again if my configurations are looking okay.
Am I missing something in this config ?
Last edited by solaris_1977; 03-05-2020 at 02:03 AM..
Reason: Corrected title
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi,
This is Solaris-10 x86 platform.
I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise.
# netstat -nr
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
LEARN ABOUT FREEBSD
gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD