03-02-2020
if the HBA are connected to SAn switches, I will to verify in errors appear in the ports, exits several types or errors, each type of errors could be help to identify the root cause, inclusive exist piort configuration that could be wrong.
What brand of FC switche are?
10 More Discussions You Might Find Interesting
1. Solaris
Has anyone configured one of these things, I cant seem to find any documentation on sunsolve, I want to verify that it is up and running... (1 Reply)
Discussion started by: csaunders
1 Replies
2. Solaris
Hi all,
I have a compatibly issues with a new hardware
My config is the following one :
Solaris 10
V490 Hardware
2 X HBA Qlogic 2310f cards
An HP EVA 5000 for storage ...
Veritas VxVM 4.1 MP1
When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
Discussion started by: unclefab
0 Replies
3. HP-UX
I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge)
Please write screenshot from utility fcutil whith test option.
Pawel (0 Replies)
Discussion started by: pawel_ul
0 Replies
4. UNIX for Advanced & Expert Users
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Discussion started by: ronbarak
3 Replies
5. Solaris
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
Discussion started by: ronbarak
4 Replies
6. Solaris
I installed a FC array for the first time and everything looks OK
in mpathadm, cfgadm, but I don't know what to do next.
# stmsboot -L
non-STMS device name STMS device name
------------------------------------------------------------------
/dev/rdsk/c2t1d0 ... (3 Replies)
Discussion started by: photon
3 Replies
7. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
8. Solaris
Hello all,
how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks
Best Regards (2 Replies)
Discussion started by: bogacd
2 Replies
9. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
10. Solaris
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
LEARN ABOUT CENTOS
ldns-verify-zone
ldns-verifyzone(1) General Commands Manual ldns-verifyzone(1)
NAME
ldns-verify-zone - read a DNSSEC signed zone and verify it.
SYNOPSIS
ldns-verify-zone ZONEFILE
DESCRIPTION
ldns-verify-zone reads a DNS zone file and verifies it.
RRSIG resource records are checked against the DNSKEY set at the zone apex.
Each name is checked for an NSEC(3), if appropriate.
OPTIONS
-h Show usage and exit
-a Apex only, check only the zone apex
-e period
Signatures may not expire within this period. Default no period is used.
-i period
Signatures must have been valid at least this long. Default signatures should just be valid now.
-k file
A file that contains a trusted DNSKEY or DS rr. This option may be given more than once.
Alternatively, if -k is not specified, and a default trust anchor (/var/lib/unbound/root.key) exists and contains a valid DNSKEY or
DS record, it will be used as the trust anchor.
-p [0-100]
Only check this percentage of the zone. Which names to check is determined randomly. Defaults to 100.
-S Chase signature(s) to a known key. The network may be accessed to validate the zone's DNSKEYs. (implies -k)
-t YYYYMMDDhhmmss | [+|-]offset
Set the validation time either by an absolute time value or as an offset in seconds from the current time.
-v Show the version and exit
-V number
Set the verbosity level (default 3):
0: Be silent
1: Print result, and any errors
2: Same as 1 for now
3: Print result, any errors, and the names that are
being checked
4: Same as 3 for now
5: Print the zone after it has been read, the result,
any errors, and the names that are being checked
periods are given in ISO 8601 duration format:
P[n]Y[n]M[n]DT[n]H[n]M[n]S
If no file is given standard input is read.
FILES
/var/lib/unbound/root.key
The file from which trusted keys are loaded for signature chasing, when no -k option is given.
SEE ALSO
unbound-anchor(8)
AUTHOR
Written by the ldns team as an example for ldns usage.
REPORTING BUGS
Report bugs to <ldns-team@nlnetlabs.nl>.
COPYRIGHT
Copyright (C) 2008 NLnet Labs. This is free software. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
27 May 2008 ldns-verifyzone(1)