02-20-2020
You did not mention, are you running a dynamic routing protocol like OSPF, RIP, EIGRP or IS-IS in your network?
9 More Discussions You Might Find Interesting
1. Programming
Hello all,
I have the following question:
if you join a multicast group (with setsockopt() and IP_ADD_MEMBERSHIP) and specify INADDR_ANY as network interface to join on, the kernel is supposed to choose which interface to use (if there are multiple network interfaces, of course).
Does... (2 Replies)
Discussion started by: AlexI
2 Replies
2. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
3. Solaris
I'm not an advanced user by any strech, that being said here is my problem:
I ran "reboot" on a sun blade 2500
When loading up it runs through the usual routine, checking disks, filesystems and then it locks up
after the following message:
*****
starting rpc services: rpcbind... (6 Replies)
Discussion started by: eyukins
6 Replies
4. Solaris
Hi all,
I would like to force the LAN card to use 10MB instead of 100MB in UNIX enviroment, please help. thanks! :) (3 Replies)
Discussion started by: Felixkoo
3 Replies
5. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
6. HP-UX
Hello,
I'm writing to you because I encountered the following problem. My program displayes all network interfaces that are available in the system, but I would like to add a functionality in which a user can enter a destination address IP (ex. the IP address of the Google search engine) and will... (1 Reply)
Discussion started by: foxrafi
1 Replies
7. Solaris
Hi,
I am using the ce interface on my Solaris 9 server and there is significant packet loss when transmitting large packets. Does anyone have a fix for this?
----10.1.0.0 PING Statistics----
51 packets transmitted, 42 packets received, 17% packet loss
round-trip (ms) min/avg/max =... (12 Replies)
Discussion started by: sparcman
12 Replies
8. AIX
(5 Replies)
Discussion started by: Vishal_dba
5 Replies
9. IP Networking
RHEL 7.0, IPV6
Scenario:
I have routed specific network using network scripts.
1. "ip -6 route show" shows that route has been added. ( with metric 1024)
2. Ping of the specific IP through that route is successful.
3. Now after few days, for some reason, we see that cache route appears for... (3 Replies)
Discussion started by: msr1981
3 Replies
LEARN ABOUT OSF1
ripquery
ripquery(8) System Manager's Manual ripquery(8)
NAME
ripquery - Queries RIP gateways
SYNOPSIS
/usr/sbin/ripquery [-1] [-2] [-[a5] authkey] [-n]
[-p] [-r] [-v] [-w time] gateway ...
FLAGS
Sends the query as a version 1 packet. Sends the query as a version 2 packet (default). Specifies the authentication password to use for
queries. If -a specified, an authentication type of SIMPLE will be used, if -5 is specified, an authentication type of MD5 will be used,
otherwise the default is an authentication type of NONE. Authentication fields in incoming packets will be displayed, but not validated.
Prevents the address of the responding host from being looked up to determine the symbolic name. Uses the RIP POLL command to request
information from the routing table. This is the default. If there is no response to the RIP POLL command, the RIP REQUEST command is
tried. The gated daemon responds to a POLL command with all the routes learned through RIP. Used the RIP REQUEST command to request
information from the gateway's routing table. Unlike the RIP POLL command, all gateways should support the RIP REQUEST. If there is no
response to the RIP REQUEST command, the RIP POLL command is tried. The gated daemon responds to a REQUEST command with all the routes he
announces out the specified interface. Because of limitations in the UDP interface, on systems based on BSD 4.3 Reno or earlier, REQUESTs
respond about the interface used to route packets back to the sender. This can be avoided by running ripquery on the host being queried.
Displays version information about ripquery before querying the gateways. Specifies the time in seconds to wait for the initial response
from a gateway. The default value is 5 seconds.
DESCRIPTION
The ripquery command is used to request all routes known by a RIP gateway by sending a RIP request or POLL command. The routing informa-
tion in any routing packets returned is displayed numerically and symbolically. The ripquery command is intended to be used as a tool for
debugging gateways, not for network management. SNMP is the preferred protocol for network management.
The ripquery command by default uses the RIP POLL command, which is an undocumented extension to the RIP specification supported by routed
on SunOS 3.x and later and by gated 1.4 and later. The RIP POLL command is preferred over the RIP REQUEST command because it is not sub-
ject to Split Horizon or Poisoned Reverse. See the RIP RFC for more information.
RELATED INFORMATION
Commands: gated(8), gdc(8), ospf_monitor(8), routed(8) delim off
ripquery(8)