02-20-2020
You did not mention, are you running a dynamic routing protocol like OSPF, RIP, EIGRP or IS-IS in your network?
9 More Discussions You Might Find Interesting
1. Programming
Hello all,
I have the following question:
if you join a multicast group (with setsockopt() and IP_ADD_MEMBERSHIP) and specify INADDR_ANY as network interface to join on, the kernel is supposed to choose which interface to use (if there are multiple network interfaces, of course).
Does... (2 Replies)
Discussion started by: AlexI
2 Replies
2. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
3. Solaris
I'm not an advanced user by any strech, that being said here is my problem:
I ran "reboot" on a sun blade 2500
When loading up it runs through the usual routine, checking disks, filesystems and then it locks up
after the following message:
*****
starting rpc services: rpcbind... (6 Replies)
Discussion started by: eyukins
6 Replies
4. Solaris
Hi all,
I would like to force the LAN card to use 10MB instead of 100MB in UNIX enviroment, please help. thanks! :) (3 Replies)
Discussion started by: Felixkoo
3 Replies
5. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
6. HP-UX
Hello,
I'm writing to you because I encountered the following problem. My program displayes all network interfaces that are available in the system, but I would like to add a functionality in which a user can enter a destination address IP (ex. the IP address of the Google search engine) and will... (1 Reply)
Discussion started by: foxrafi
1 Replies
7. Solaris
Hi,
I am using the ce interface on my Solaris 9 server and there is significant packet loss when transmitting large packets. Does anyone have a fix for this?
----10.1.0.0 PING Statistics----
51 packets transmitted, 42 packets received, 17% packet loss
round-trip (ms) min/avg/max =... (12 Replies)
Discussion started by: sparcman
12 Replies
8. AIX
(5 Replies)
Discussion started by: Vishal_dba
5 Replies
9. IP Networking
RHEL 7.0, IPV6
Scenario:
I have routed specific network using network scripts.
1. "ip -6 route show" shows that route has been added. ( with metric 1024)
2. Ping of the specific IP through that route is successful.
3. Now after few days, for some reason, we see that cache route appears for... (3 Replies)
Discussion started by: msr1981
3 Replies
LEARN ABOUT HPUX
ripquery
ripquery(1M) ripquery(1M)
NAME
ripquery - query RIP gateways
SYNOPSIS
authkey] dest[time] gateway ...
DESCRIPTION
is used to request all routes known by a RIP gateway by sending a RIP request or POLL command. The routing information in any routing pack-
ets returned is displayed numerically and symbolically. is intended to be used as a tool for debugging gateways, not for network manage-
ment. SNMP is the preferred protocol for network management.
by default uses the RIP POLL command, which is an undocumented extension to the RIP specification supported by on SunOS 3.x and later and
by 1.4 and later. The RIP POLL command is preferred over the RIP REQUEST command because it is not subject to Split Horizon and/or Poi-
soned Reverse. See the RIP RFC for more information.
Options
Send the query as a version 1 packet.
Send the query as a version 2 packet (default).
Specifies the authentication password to use for queries. If
specified, an authentication type of SIMPLE will be used, if is specified, an authentication type of MD5 will be used; oth-
erwise the default is an authentication type of NONE. Authentication fields in incoming packets will be displayed, but not
validated.
Prevents the address of the responding host from being looked up
to determine the symbolic name.
Specifies that the query should be for the specified
instead of complete routing table. The specification of the optional mask implies a version 2 query. Up to 23 requests about
specific destinations may be include in one packet.
Uses the RIP POLL command to request information from the routing
table. This is the default, but is an undocumented extension supported only by some versions of unOS 3.x and later versions
of If there is no response to the RIP POLL command, the RIP REQUEST command is tried. responds to a POLL command with all
the routes learned via RIP.
Used the RIP REQUEST command to request information from the
gateway's routing table. Unlike the RIP POLL command, all gateways should support the RIP REQUEST. If there is no response
to the RIP REQUEST command, the RIP POLL command is tried. responds to a REQUEST command with all the routes he announces
out the specified interface. Due to limitations in the UDP interface, on systems based on BSD 4.3 Reno or earlier, REQUESTs
respond about the interface used to route packets back to the sender. This can be avoided by running on the host being
queried.
Version information about
is displayed before querying the gateways.
Specifies the time in seconds to wait for the initial response
from a gateway. The default value is 5 seconds.
AUTHORS
Jeffrey C Honig.
SEE ALSO
gated(1M), gdc(1M), ospf_monitor(1M),
BUGS
Some versions of Unix do not allow looking up the symbolic name of a subnet.
ripquery(1M)