I think I have failed to articulate the problem. Let me try again.
The client, in the first attempts, append the domainname (as it is in the resolv.conf). If the record is not found then it tries again -- this time it drops the domainname. How do I stop the 2nd attempt or dropping of the domain?
The tcpdump when the above command was run:
Please observe that the domain name , biman.net has been appended only in the first appempt
hi gurus,
need to check other than the hosts file, what else i need to change after we have changed the domain name in our company. currently, we are using olddnsname.com and will change it to newdnsname.com. i am not sure where else in solaris i need to take a look.
please advise.
thank... (4 Replies)
Dear Expert,
i have linux box that is running in the windows domain, BUT did not being a member of the domain. as I am not the System Administrator so I have no control on the server in the network, such as modify dns entry , add the linux box in AD and domain record and so on that relevant.
... (2 Replies)
Hello,
I'm using CentOS 5.3, and I connect to a VPN in order to work. The problem is that I'm constantly accessing things on the local network and the remote network. But once I'm connected to the VPN I can't access local addresses by name, I have to use the ip-address.
What I'd like is to... (4 Replies)
Hi everybody,
for revolving local host name of my network, I set up an dns server to solve my problem, but til now, nothing happen when I ping a hostname, but work on IP. Can you help me to correct the configuration. Here is all my settings:
Voici mes fichiers de configuration:
-... (2 Replies)
I'd like to get some opnions on choosing DNS server:
Windows DNS vs Linux BIND comparrsion:
1) managment, easy of use
2) Security
3) features
4) peformance
5) ??
I personally prefer Windows DNS server for management, it supports GUI and command line. But I am not sure about security... (2 Replies)
Hello to all,
May you help saying me how to flush a specific domain in Linux SunOS5
I know the command rndc is to flush DNS cache, but I would like to know:
1- How to do a flush only on specific domain
2- How to see the content of DNS Resolver cache (similar to info given by IPCONFIG... (2 Replies)
I have read many tutorials on bind and i understand the A,MX, CNAME records.
Internally, on a LAN we can install bind and create all these records and we can tell all PC and servers to use this bind as DNS server.that's fine.
On the Internet, when we have purchased a valid domain like... (5 Replies)
I am writing the following script to create the file v_out.txt.
sqlplus -s /nolog << EOF
CONNECT scott/tiger@orcl;
whenever sqlerror exit sql.sqlcode;
set newpage 0;
SET PAGESIZE 0;
SET ECHO OFF;
SET FEEDBACK OFF;
SET HEADING OFF;
SET VERIFY OFF;
SET LINESIZE 100;
set tab off;
set... (7 Replies)
Hello,
Our organization is planning to move one domain from Dreamhost to Hubspot. Lets say, it is gem.xyxyxyxyx.com. Please note, website is not being migrated from one server to another, it is just hosting company.
Here is from our internal DNS master server -
# cat... (6 Replies)
Discussion started by: solaris_1977
6 Replies
LEARN ABOUT FREEBSD
gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD