My Fc cards on T4-2 servrs are
now bencmarking is already done by another team and its ok as the same is working in other data cntre very well
--- Post updated at 01:39 PM ---
i have changed the cables connecting machines to storage controller and then change the SFPS in FC cards even the issue persist. then i also change the ports at
Fiber switch but issue remains the same . now from the same switch and on the same WWN on storgae controller we have another database running + other chaisis but no issue there so i guess it will be the FC cards which is messing so that why i asked for any commnds to check the constant connectivity of this FC cards or any thing else for the same purpose
Hi all,
I have a compatibly issues with a new hardware
My config is the following one :
Solaris 10
V490 Hardware
2 X HBA Qlogic 2310f cards
An HP EVA 5000 for storage ...
Veritas VxVM 4.1 MP1
When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge)
Please write screenshot from utility fcutil whith test option.
Pawel (0 Replies)
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
I installed a FC array for the first time and everything looks OK
in mpathadm, cfgadm, but I don't know what to do next.
# stmsboot -L
non-STMS device name STMS device name
------------------------------------------------------------------
/dev/rdsk/c2t1d0 ... (3 Replies)
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
LEARN ABOUT DEBIAN
install-solaris
install-solaris(1M)install-solaris(1M)NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)