Sponsored Content
Operating Systems Solaris Issue with Fiber Channel cards in Solaris Post 303043272 by hicksd8 on Thursday 23rd of January 2020 05:08:35 AM
Old 01-23-2020
My first questions are (1) What make/model of storage is it? (2) What make/model of FC cards?

The first place I would be looking is the link configuration(s). The expensive FC cards are highly configurable beasts and the settings need to be compatible with the hardware at the other end of the link. Under pressure, the storage controller might dispatch a packet with a higher payload than the FC card buffer is configured to take causing data to be lost, protocol recovery to be invoked (unsuccessfully), etc, etc.

Have you run an I/O benchmark between Solaris and the storage to see the performance and, more importantly, whether that breaks too.
This User Gave Thanks to hicksd8 For This Post:
 

10 More Discussions You Might Find Interesting

1. Solaris

x25 cards on solaris 8

Has anyone configured one of these things, I cant seem to find any documentation on sunsolve, I want to verify that it is up and running... (1 Reply)
Discussion started by: csaunders
1 Replies

2. Solaris

VxVM/Hba cards/Solaris 10 FS issue

Hi all, I have a compatibly issues with a new hardware My config is the following one : Solaris 10 V490 Hardware 2 X HBA Qlogic 2310f cards An HP EVA 5000 for storage ... Veritas VxVM 4.1 MP1 When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
Discussion started by: unclefab
0 Replies

3. HP-UX

Fiber Channel statistic & error level

I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge) Please write screenshot from utility fcutil whith test option. Pawel (0 Replies)
Discussion started by: pawel_ul
0 Replies

4. UNIX for Advanced & Expert Users

How do I know which HBA cards' hardware I have (on Solaris 10) ?

Hi, I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine. The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards. Can anyone suggest how to determine my HBA hardware ? Thanks, Ron. ... (3 Replies)
Discussion started by: ronbarak
3 Replies

5. Solaris

How do I know which HBA cards' hardware I have (on Solaris 10) ?

Hi, I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine. The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards. Can anyone suggest how to determine my HBA hardware ? Thanks, Ron. ... (4 Replies)
Discussion started by: ronbarak
4 Replies

6. Solaris

Fiber Channel StorageTek Array Visible to OS

I installed a FC array for the first time and everything looks OK in mpathadm, cfgadm, but I don't know what to do next. # stmsboot -L non-STMS device name STMS device name ------------------------------------------------------------------ /dev/rdsk/c2t1d0 ... (3 Replies)
Discussion started by: photon
3 Replies

7. Solaris

USCSICMD ioctl calls for Fibre Channel(FC) devices on Solaris 10?

Hi , I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies

8. Solaris

Solaris 10 new fiber connected tape

Hello all, how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks Best Regards (2 Replies)
Discussion started by: bogacd
2 Replies

9. IP Networking

Channel bonding Issue - Bond0 interface not getting up in on RHEL6

Hello, I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies

10. Solaris

Fibre channel link down on booting Solaris server

Hi I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10. After power on the system stops at ok prompt, them I issued the following commands: {0} ok setenv auto-boot? false auto-boot? = false {0} ok reset-all SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
DAIC(4) 						   BSD Kernel Interfaces Manual 						   DAIC(4)

NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10 DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO. For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd system, which can be listed using the daicctl utility. The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto- col and some parts of the cards interface are ISDN protocol dependent. The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992. MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd. Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu- mentation for details. The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte- grated. But if you own a card, you do have the file (or can get it from the Diehl web server). SEE ALSO
daicctl(1) BUGS
The driver is not yet finished. BSD
January 30, 1998 BSD
All times are GMT -4. The time now is 04:25 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy