hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but till then my database instance get crashes. so i want to confirm from my machines that whether fiber cards is ok. i usually use
it always connected and says online
plz guide what else should i check , any commands etc
regards
Moderator's Comments:
It is a bit hard to understand your post when you do not check your spelling . Please use your in browser spell checker before posting.
Hi all,
I have a compatibly issues with a new hardware
My config is the following one :
Solaris 10
V490 Hardware
2 X HBA Qlogic 2310f cards
An HP EVA 5000 for storage ...
Veritas VxVM 4.1 MP1
When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge)
Please write screenshot from utility fcutil whith test option.
Pawel (0 Replies)
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
I installed a FC array for the first time and everything looks OK
in mpathadm, cfgadm, but I don't know what to do next.
# stmsboot -L
non-STMS device name STMS device name
------------------------------------------------------------------
/dev/rdsk/c2t1d0 ... (3 Replies)
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
LEARN ABOUT DEBIAN
canfield
CANFIELD(6) BSD Games Manual CANFIELD(6)NAME
canfield, cfscores -- the solitaire card game canfield
SYNOPSIS
canfield
cfscores [-a] [user]
DESCRIPTION
If you have never played solitaire before, it is recommended that you consult a solitaire instruction book. In Canfield, tableau cards may be
built on each other downward in alternate colors. An entire pile must be moved as a unit in building. Top cards of the piles are available to
be played on foundations, but never into empty spaces.
Spaces must be filled from the stock. The top card of the stock also is available to be played on foundations or built on tableau piles.
After the stock is exhausted, tableau spaces may be filled from the talon and the player may keep them open until he wishes to use them.
Cards are dealt from the hand to the talon by threes and this repeats until there are no more cards in the hand or the player quits. To have
cards dealt onto the talon the player types 'ht' for his move. Foundation base cards are also automatically moved to the foundation when
they become available.
The command 'c' causes canfield to maintain card counting statistics on the bottom of the screen. When properly used this can greatly
increase one's chances of winning.
The rules for betting are somewhat less strict than those used in the official version of the game. The initial deal costs $13. You may
quit at this point or inspect the game. Inspection costs $13 and allows you to make as many moves as possible without moving any cards from
your hand to the talon. (The initial deal places three cards on the talon; if all these cards are used, three more are made available.)
Finally, if the game seems interesting, you must pay the final installment of $26. At this point you are credited at the rate of $5 for each
card on the foundation; as the game progresses you are credited with $5 for each card that is moved to the foundation. Each run through the
hand after the first costs $5. The card counting feature costs $1 for each unknown card that is identified. If the information is toggled
on, you are only charged for cards that became visible since it was last turned on. Thus the maximum cost of information is $34. Playing
time is charged at a rate of $1 per minute.
With no arguments, the program cfscores prints out the current status of your canfield account. If a user name is specified, it prints out
the status of their canfield account. If the -a flag is specified, it prints out the canfield accounts for all users that have played the
game since the database was set up.
FILES
/usr/games/canfield the game itself
/usr/games/cfscores the database printer
/var/games/bsdgames/cfscores
the database of scores
BUGS
It is impossible to cheat.
AUTHORS
Originally written: Steve Levine.
Further random hacking by: Steve Feldman, Kirk McKusick, Mikey Olson, and Eric Allman.
BSD May 31, 1993 BSD