It depends quite what you are looking for. Do any of these help (sorry but I no longer have access to AIX so I'm a bit rusty!)
What are the metrics you are looking for? Is it the LPAR view of the assigned disk to the size of the disk that is owned by the hardware as a whole? The LPAR will not see that.
I hope that these suggestions give you something.
Robin
Thank Robin, I would like to check at the physical hardware console, not from LPAR, have not LPAR right now.
--- Post updated at 06:13 AM ---
Quote:
Originally Posted by zxmaus
from the hardware itself, you cannot see the disks - you can only see the controllers, not what is attached to them.
As part of the SMS menu you can see the disks and sizes if you query the controllers - or when you install AIX as you have to select a suitable disks for the installation - with location code.
If you have AIX already installed, run these commands.
to find your SAS disks, run
to figure out the disk size of said disks use
Hi Zxmaus,
I understand now that from physical hardware Power Machine we cannot check the disk and size.
Still have 1 thing to ask, for SAS disk, I see it is part of raid controller. The disk is called pdisk. After configuring raid, it becomes hdisk which AIX can see. The question is, if in the first time, we assign the controller and its disks to LPAR to install AIX. How can we configure the raid before AIX OS can see these disks?
I have two Unix machines on the network and now one of them are running out of disk but i have alot on the other so i like to mount the disk (or a folder) from the one that has disk and mount it on the other that does not.
How do i do that? Is it possible i read the "man mount" but didn't really... (5 Replies)
Hi!!
I am these days working on a project, where I need to know about the disk controllers available in a machine (e.g., 3ware,IBM,etc).
Please, let me know the command by which I can get the information.
thnx,
priyanka (3 Replies)
Hello All,
Can anybody please tell me what is the maximum limit of Physical IBM Power Machine which can be handled by single HMC at a single point of time?
Thanks,
Jenish (1 Reply)
Hello,
I have a quick question regarding POWER HA ( HACMP ) 5.5 ;
I have four ethernet adapters
en0
en1
en2
en3
en0 is configured as BOOT_IP with IP address
all other ethernet adapters are empty en1 / en2 / en3
so when I configure the service IP and start HACMP , the service IP... (2 Replies)
Hi,
Is there an easy way to find the disk-type from the command line or with another api ? sdparm works for SAS but not for SATA, hdparm works for SATA but not SAS.
Thanks (1 Reply)
hi guys,
I don't like the new concept of the power ha 7 cluster with the repository disk and the internal solidb, I really would like to mirror this disk, but the "IBM PowerHA SystemMirror 7.1 for AIX" redbook says, normal lvm operations should not be performed on this disk.
even mirroring the... (0 Replies)
Hi
Is there any native commands or somewhere in the /proc files to get the machine's power consumption? I googled for a while and cannot really find this information
Thanks for your help. (6 Replies)
I need to add a VMware virtual disk to the 99-oracle-asmdevices.rules file but the OS is not assigning a WWID to the disk. It has been fdisk'd and a single partition created.
What TAG inside the file needs to be added? the Program scsi-id does not work for some reason. latest patches... (0 Replies)
Hi,
I have installed the HMC on the VMWare VM. I try to add the power machine (managed system) and asking for a password? So this is the IBM predefined password of Power Machine?
In the VMWare perspective, we can login to ESX host to do some management tasks. But how about the Power machine?... (6 Replies)
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
LEARN ABOUT HPUX
vxpfto
vxpfto(1M)vxpfto(1M)NAME
vxpfto - set Powerfail Timeout (pfto)
SYNOPSIS
vxpfto -g diskgroup -t timeout
vxpfto [-g diskgroup] -t timeout volume_list
vxpfto [-g diskgroup] -o pftostate={enabled|disabled}
vxpfto [-g diskgroup] -o pftostate={enabled|disabled} volume_list
DESCRIPTION
Powerfail Timeout is an attribute of a SCSI disk connected to an HP-UX host (see the pfto(7) man page). The vxpfto command sets the Power-
fail Timeout interval on a set of Volume Manager disks, either all disks in a disk group, or all disks underlying the volumes listed.
The first form of the command sets the same PFTO value for all the disks in the specified VxVM diskgroup.
In the second form, all disks underlying the given list of volumes are selected, optionally restricted by the disk group specified with the
-g option. If you specify a diskgroup, any volume in the list not belonging to the diskgroup is ignored.
Use the -o pftostate option to disable or enable PFTO. By default, PFTO is enabled. You can enable PFTO either on all disks in a disk
group, or on all disks underlying the volumes listed.
If you invoke vxpfto without arguments, it displays a usage message.
OPTIONS -g diskgroup
Specifies the disk group for the operation, either by disk group ID or by disk group name.
-o pftostate={enabled|disabled}
Enables or disables the use of PFTO for IO.
-t timeout
Specifies the PFTO value in seconds. The value must be zero or a positive integer. Zero represents the system default PFTO
value. The default value depends on the disk driver controlling the disk device.
volume_list
A list of VxVM volume names. List items must be separated by white-space.
EXIT CODES
vxpfto returns a zero if successful. If it encounters an error, vxpfto exits and displays a message on standard error. Defined exit codes
are:
0 Success.
1 No PFTO value specified.
2 No diskgroup or volume list specified.
3 Illegal PFTO value specified.
EXAMPLES
Set the PFTO value on all disks in disk group testdg to 100 seconds:
vxpfto -t 100 -g testdg
Set the PFTO value to 50 seconds on all disks underlying volume01 and volume02 in disk group testdg:
vxpfto -t 50 -g testdg volume01 volume02
Set the PFTO value to 300 seconds on all disks underlying volume01 and volume02, even though they are not in the same disk group:
vxpfto -t 300 volume01 volume02
Disable PFTO on all disks in disk group testdg:
vxpfto -g testdg -o pftostate=disabled
Enable PFTO on all disks underlying volume01 and volume02i in disk group testdg:
vxpfto -g testdg -o pftostate=enabled volume01 volume02
SEE ALSO vxdisk(1M), pfto(7)VxVM 5.0.31.1 24 Mar 2008 vxpfto(1M)