Sponsored Content
Operating Systems SCO SCO OS 6 Driver for LSIL SAS1064E Raid Controller Post 303042363 by jgt on Sunday 22nd of December 2019 09:02:02 PM
Old 12-22-2019
You have to run mkdev hd.

Make sure you do not format the disk or change any sizes.

In divvy, you have to rename the root partition from hd0root to something else that is not currently used on any hard drive.

Be very careful to not mark this partition as new, as it will be formatted if you do.

Once this is done, you can mount the partition to /oldroot, or some other name.

You must refer to files in the old root file system by their full name, in the case of /etc/shadow, this will be /oldroot/var/opt/SCO/.Unix.6.0.0Ni/etc/shadow.

If you do not, simply referring to /oldroot/etc/shadow, will be linked to /var/opt... in the booted root file system.

Last edited by Neo; 12-22-2019 at 10:24 PM.. Reason: Code Tags Please See YT Video on this: https://youtu.be/4BuPvWJV__k
 

10 More Discussions You Might Find Interesting

1. SCO

ultra 320 scsi raid controller driver for sco 5.0.6

I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller . how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6. Plz help with any idea karzon (1 Reply)
Discussion started by: karzon
1 Replies

2. SCO

driver needed for hp smartarry p200i sas raid controller

recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies

3. Solaris

RAID controller needed for SVM?

hi this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network) i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies

4. Hardware

Problem with External Raid Controller.

Hi, We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks. This also has an External Raid Controller (Storagetek Eight-Port, External HBA Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk. ... (1 Reply)
Discussion started by: ranjansukumar
1 Replies

5. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies

6. AIX

Internal PCI X RAID Controller issue ?

Hello folks, Could someone tell me why I unable to create pdisks for a RAID Array # lscfg | grep scsi + sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter + scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies

7. Red Hat

RAID Configuration for IBM Serveraid-7k SCSI RAID Controller

Hello, I want to delete a RAID configuration an old server has. Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton? I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies

8. SCO

How to change raid controller driver ? (hardware change)

Hello I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller . The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver) What ... (3 Replies)
Discussion started by: flako
3 Replies

9. Red Hat

Separate HDD test using RAID controller

Hello, I am using Red Hat 2.6.23.1 with RAID 6 controller (card). (When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.) I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies

10. SCO

SCO 5.0.7 driver for HP SmartArray P410i Controller on Proliant DL380 G7?

Hi I hope this is the right forum. I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller. I need a driver for this. Can anybody point me to a download? Thanks in anticipation. (12 Replies)
Discussion started by: Stuart1946
12 Replies
scrounge-ntfs(8)					    BSD System Manager's Manual 					  scrounge-ntfs(8)

NAME
scrounge-ntfs -- helps retrieve data from corrupted NTFS partitions SYNOPSIS
scrounge-ntfs -l disk scrounge-ntfs -s disk scrounge-ntfs [-m mftoffset] [-c clustersize] [-o outdir] disk start end DESCRIPTION
scrounge-ntfs is a utility that can rescue data from corrupted NTFS partitions. It writes the files retrieved to another working file system. Certain information about the partition needs to be known in advance. The -l mode is meant to be run in advance of the data corruption, with the output stored away in a file. This allows scrounge-ntfs to recover data reliably. See the 'NOTES' section below for recover info when this isn't the case. OPTIONS
The options are as follows: -c The cluster size (in sectors). When not specified a default of 8 is used. -l List partition information for a drive. This will only work when the partition table for the given drive is intact. -m When recovering data this specifies the location of the MFT from the beginning of the partition (in sectors). If not specified then no directory information can be used, that is, all rescued files will be written to the same directory. -o Directory to put rescued files in. If not specified then files will be placed in the current directory. -s Search disk for partition information. (Not implemented yet). disk The raw device used to access the disk which contains the NTFS partition to rescue files from. eg: '/dev/hdc' start The beginning of the NTFS partition (in sectors). end The end of the NTFS partition (in sectors) NOTES
If you plan on using this program sucessfully you should prepare in advance by storing a copy of the partition information. Use the -l option to do this. Eventually searching for disk partition information will be implemented, which will solve this problem. When only one partition exists on a disk or you want to rescue the first partition there are ways to guess at the sector sizes and MFT loca- tion. See the scrounge-ntfs web page for more info: http://memberwebs.com/swalter/software/scrounge/ AUTHOR
Stef Walter <stef@memberwebs.com> scrounge-ntfs June 1, 2019 scrounge-ntfs
All times are GMT -4. The time now is 08:23 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy