Sponsored Content
Operating Systems SCO SCO OS 6 Driver for LSIL SAS1064E Raid Controller Post 303042363 by jgt on Sunday 22nd of December 2019 09:02:02 PM
Old 12-22-2019
You have to run mkdev hd.

Make sure you do not format the disk or change any sizes.

In divvy, you have to rename the root partition from hd0root to something else that is not currently used on any hard drive.

Be very careful to not mark this partition as new, as it will be formatted if you do.

Once this is done, you can mount the partition to /oldroot, or some other name.

You must refer to files in the old root file system by their full name, in the case of /etc/shadow, this will be /oldroot/var/opt/SCO/.Unix.6.0.0Ni/etc/shadow.

If you do not, simply referring to /oldroot/etc/shadow, will be linked to /var/opt... in the booted root file system.

Last edited by Neo; 12-22-2019 at 10:24 PM.. Reason: Code Tags Please See YT Video on this: https://youtu.be/4BuPvWJV__k
 

10 More Discussions You Might Find Interesting

1. SCO

ultra 320 scsi raid controller driver for sco 5.0.6

I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller . how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6. Plz help with any idea karzon (1 Reply)
Discussion started by: karzon
1 Replies

2. SCO

driver needed for hp smartarry p200i sas raid controller

recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies

3. Solaris

RAID controller needed for SVM?

hi this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network) i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies

4. Hardware

Problem with External Raid Controller.

Hi, We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks. This also has an External Raid Controller (Storagetek Eight-Port, External HBA Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk. ... (1 Reply)
Discussion started by: ranjansukumar
1 Replies

5. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies

6. AIX

Internal PCI X RAID Controller issue ?

Hello folks, Could someone tell me why I unable to create pdisks for a RAID Array # lscfg | grep scsi + sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter + scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies

7. Red Hat

RAID Configuration for IBM Serveraid-7k SCSI RAID Controller

Hello, I want to delete a RAID configuration an old server has. Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton? I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies

8. SCO

How to change raid controller driver ? (hardware change)

Hello I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller . The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver) What ... (3 Replies)
Discussion started by: flako
3 Replies

9. Red Hat

Separate HDD test using RAID controller

Hello, I am using Red Hat 2.6.23.1 with RAID 6 controller (card). (When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.) I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies

10. SCO

SCO 5.0.7 driver for HP SmartArray P410i Controller on Proliant DL380 G7?

Hi I hope this is the right forum. I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller. I need a driver for this. Can anybody point me to a download? Thanks in anticipation. (12 Replies)
Discussion started by: Stuart1946
12 Replies
CFREE(3)						     Linux Programmer's Manual							  CFREE(3)

NAME
cfree - free allocated memory SYNOPSIS
#include <stdlib.h> /* In SunOS 4 */ int cfree(void *ptr); /* In glibc or FreeBSD libcompat */ void cfree(void *ptr); /* In SCO OpenServer */ void cfree(char *ptr, unsigned num, unsigned size); /* In Solaris watchmalloc.so.1 */ void cfree(void *ptr, size_t nelem, size_t elsize); Feature Test Macro Requirements for glibc (see feature_test_macros(7)): cfree(): _BSD_SOURCE || _SVID_SOURCE DESCRIPTION
This function should never be used. Use free(3) instead. 1-arg cfree In glibc, the function cfree() is a synonym for free(3), "added for compatibility with SunOS". Other systems have other functions with this name. The declaration is sometimes in <stdlib.h> and sometimes in <malloc.h>. 3-arg cfree Some SCO and Solaris versions have malloc libraries with a 3-argument cfree(), apparently as an analog to calloc(3). If you need it while porting something, add #define cfree(p, n, s) free((p)) to your file. A frequently asked question is "Can I use free(3) to free memory allocated with calloc(3), or do I need cfree()?" Answer: use free(3). An SCO manual writes: "The cfree routine is provided for compliance to the iBCSe2 standard and simply calls free. The num and size argu- ments to cfree are not used." RETURN VALUE
The SunOS version of cfree() (which is a synonym for free(3)) returns 1 on success and 0 on failure. In case of error, errno is set to EINVAL: the value of ptr was not a pointer to a block previously allocated by one of the routines in the malloc(3) family. CONFORMING TO
The 3-argument version of cfree() as used by SCO conforms to the iBCSe2 standard: Intel386 Binary Compatibility Specification, Edition 2. SEE ALSO
malloc(3) COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. 2007-07-26 CFREE(3)
All times are GMT -4. The time now is 07:59 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy