Yes, I now have installed a second SCO 6 instance on a 3rd hard disk in the same system and the same controller. I can now boot on that new instance and have root acceess there.
It runs in an intel Compaq box with an LSI Logic Corp MPT SAS RAID board SAS1064E-IR.
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Hello
I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller .
The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver)
What ... (3 Replies)
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Hi
I hope this is the right forum.
I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller.
I need a driver for this. Can anybody point me to a download?
Thanks in anticipation. (12 Replies)
Discussion started by: Stuart1946
12 Replies
LEARN ABOUT DEBIAN
mfi
MFI(4) BSD Kernel Interfaces Manual MFI(4)NAME
mfi -- LSI MegaRAID SAS driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device mfi
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mfi_load="YES"
DESCRIPTION
This driver is for LSI's next generation PCI Express SAS RAID controllers. Access to RAID arrays (logical disks) from this driver is pro-
vided via /dev/mfid? device nodes. A simple management interface is also provided on a per-controller basis via the /dev/mfi? device node.
The mfi name is derived from the phrase "MegaRAID Firmware Interface", which is substantially different than the old "MegaRAID" interface and
thus requires a new driver. Older SCSI and SATA MegaRAID cards are supported by amr(4) and will not work with this driver.
Two sysctls are provided to tune the mfi driver's behavior when a request is made to remove a mounted volume. By default the driver will
disallow any requests to remove a mounted volume. If the sysctl dev.mfi.%d.delete_busy_volumes is set to 1, then the driver will allow
mounted volumes to be removed.
HARDWARE
The mfi driver supports the following hardware:
o LSI MegaRAID SAS 1078
o LSI MegaRAID SAS 8408E
o LSI MegaRAID SAS 8480E
o LSI MegaRAID SAS 9260
o Dell PERC5
o Dell PERC6
o IBM ServeRAID M5015 SAS/SATA
o IBM ServeRAID-MR10i
o Intel RAID Controller SROMBSAS18E
FILES
/dev/mfid? array/logical disk interface
/dev/mfi? management interface
DIAGNOSTICS
mfid%d: Unable to delete busy device An attempt was made to remove a mounted volume.
SEE ALSO amr(4), pci(4), mfiutil(8)HISTORY
The mfi driver first appeared in FreeBSD 6.1.
AUTHORS
The mfi driver and this manual page were written by Scott Long <scottl@FreeBSD.org>.
BUGS
The driver does not support big-endian architectures at this time.
BSD May 12, 2010 BSD