I need to put the meter on the four wire output of the IR controller and get a better understanding of this three light strip (the resistance and the voltage).
At this rate, I will buy that new Rigol 1054Z sooner than later!
In my Aliexpress shopping cart for a few weeks now:
Hi all...
(Apologies for any typos at all.)
This is a step by step _script_ to check if your Arduino is talking to your Linux or Macbook Pro computer using the Terminal...
It works on at least 3 Linux flavours and now the Macbook Pro...
I hope you find it useful as a simple check for... (0 Replies)
This is a very simple starter DEMO to access Arduino Diecimila Board for the
Macbook Pro 13" OSX 10.7.5...
A potentiometer is connected between 5V and Gnd with the wiper connected to
ANALOG IN 0 on the Arduino. This was adjusted to give the Ms and Ls as seen...
I now have DC in for this... (0 Replies)
I am working on a semi-auto detection idea for Arduino for the Scope project.
It does require a little user intervention but minimal.
It works by just responding to two on screen prompts to unplug and plug Arduino
into a USB port.
There are two versions and both work perfectly well and give... (3 Replies)
In my further exploration of Arduino, today I decided to install the arduino-cli on my mac today.
https://github.com/arduino/arduino-cli
I followed the instructions for macOS but when I got to this part:
arduino-cli board list
I got the dreaded "Unknown" Fully Qualified Board Name... (1 Reply)
HI all...
(Apologies for any typos.)
To add to Neo's Arduino subject matter I have decided to upload this in ".zip" format.
Ignore "*.info" files these are AMIGA icons only and also the "HAM" drawer as these are photos in ancient AMIGA HAM modes.
I have noticed that there are current... (6 Replies)
Waiting for more fun Ardunio parts from AliExpress, I decided to test two cheap Chinese Arduino UNO clones.
The Arduino UNO R3 (CH340G) MEGA328P
The Wavgat UNO R3 (CH340G) MEGA328P
Both of these Chinese Ardunio clones sell for about $3 USD, delivered to your door.
The bottom line is... (0 Replies)
Just finished a quick Python script to send the current unix time over to the Arduino from macOS, so in the absence of GPS or some other way to get the unix timestamp (epoch time) to the Arduino, I can get my macOS and Arduino UNO synced to within a second.
Normally, when the Arduino starts... (9 Replies)
Here is a sketch to do basic testing for the Arduino UNO and the MLT-BT04.
This BLE module works with IOS (iPhone) and I'll add some details on my IOS testing with an iPhone in a follow-up post.
For now, here is the basic BLE (HM-10) sketch for the Arduino UNO:
/*
Arduino test-code... (7 Replies)
Discussion started by: Neo
7 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)