When your data is consistent it is easy to use awk with multiple lines like this. Can we please make this portable so I can use this in both RHEL and AIX?
What do I do when the data is not consistent? When your data is not consistent like this it does not work.
There is another problem I have. Sometimes the data has more than two lines.
Hi,
I have data with broken lines:
Sample data:
"12"|"25"|"a"|"b"|"c"|"d"|"e"|"f"|"2453748"|"08:10:50"
"16"|"25"|"a"|"b"|"c"|"d"|"e"|"f"|"
2453748"|"08:15:50"
"16"|"25"|"a"|"b"|"
c"|"d"|"e"|"f"|"2453748"|"08:19:50"
"16"|"25"|"a"|"b"|"c"|"d"|"e"|"f"|"2453748"|"08:19:50"
In the... (5 Replies)
Hi everyone!
I'm not new to Unix, but I've never used awk before.
I tried to look up this information on several sites and forums,
I also looked in the documentation but I haven't found a solution yet.
I would like to print the previous 3 lines before and the following 4 lines after the... (6 Replies)
Hi everyboby
this is my problem
I Have this input
1111;222
222
2;333
3333;4444
111;
22222;33
33;
444
and I need this output
1111;2222222;3333333;4444 (15 Replies)
say I'm doing awk 'NR==534'
Is there a way to display 534 535 536 537?
without appending to a variable? per line? maybe an easier way with a different command?
My first impression was NR==534-537 but that would be too easy :P (2 Replies)
Hi.
I need to filter lines based upon matches in multiple tab-separated columns. For all matching occurrences in column 1, check the corresponding column 4. IF all column 4 entries are identical, discard all lines. If even one entry in column 4 is different, then keep all lines.
How can I... (5 Replies)
What is the correct syntax to have the awk parse the next line as well? The next in bold is where I think it should go, but I wanted to ask the experts since I am a beginner. The file to be parsed is attached as well. Thank you :).
awk 'NR==2 {split($2,a,"");b=substr(a,1,length(a-1));print... (6 Replies)
Hello all,
I have a large csv file where there are four types of rows I need to merge into one row per person, where there is a column for each possible code / type of row, even if that code/row isn't there for that person.
In the csv, a person may be listed from one to four times... (9 Replies)
Discussion started by: RalphNY
9 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)