It is possible to install Solaris Cluster on ESXI host ?
I try many time to install and configure Solaris Cluster on ESXI, but i received the same transport error between. When i set manuel private (net1,net2) ip config i have ping between nodes.
Quote:
"Probes were sent out from all transport adapters configured for this
node ("node1"). But, they were not seen by any of the other nodes.
This may be due to any number of reasons, including improper cabling
or a switch which was confused by the probes.
You can either attempt to correct the problem and try the probes again or manually configure the transport.
on ESXI i created vSwitch1 (net1/net1) / vSwitch2 (net2/net2)
After much hitting my head to the wall with this meesages
root@crasher /workzone/dvd4_sfb-sol_x64]#./installer -verbose -installonly
5.0MP3 Installation Program
Copyright (c) 2008 Symantec Corporation. All rights reserved. Symantec, the Symantec... (1 Reply)
Greetings Forumers!
I tried installing Solaris Cluster 3.3 today. I should say I tried configuring the Cluster today. The software is already installed on two systems. I am trying to configure a shared filesystem between two 6320 Blades. I selected the "Custom" install because the "Typical"... (2 Replies)
Anybody have any ideas on what could be causing this crash? This an x86 virtual machine I have running in ESXi at my house, so obviously no way to send the data to Oracle for analysis. Just curious if anyone has any ideas. I suspect motherboard problems with the x86 hardware, as I already... (4 Replies)
how do I remote install a vib on 200 esxi hosts ?
I need to ssh into the host
run this command
esxcli software vib install -v /tmp/vib --no-sig-check (1 Reply)
Hi
i have 2 esxi. one is amd based cpu and the other is intel based cpu.
i have a redhat linux machine that was created in amd cpu esxi, now i need to migrate it (powered off) to INTEL based esxi. will the redhat machine will be OK with that?
Thanks (2 Replies)
Hi All,
Can any one Explain Me Step by Step installing SCO 5.0.7v in ESXi 6.0 ??
When i was trying to install its is not booting into operating systems !!
showing an error no operating systems in media !!
Thanks in Advance!! Please take some time in helping me !!
Kanthi Kiran K (3 Replies)
Tl;dr Solaris 11.4 won't boot on 2 machines because of what I believe is network issues. Need to know where I can find more info to troubleshoot.
I have two Solaris 11.4 systems running on VMware ESXi 6.5u2, which have suddenly (and seemingly for no reason) started boot-looping.
Both of... (2 Replies)
Discussion started by: rking267
2 Replies
LEARN ABOUT DEBIAN
paranoid::network::ipv4
Paranoid::Network::IPv4(3pm) User Contributed Perl Documentation Paranoid::Network::IPv4(3pm)NAME
Paranoid::Network::IPv4 - IPv4-related functions
VERSION
$Id: IPv4.pm,v 0.1 2012/05/29 21:37:44 acorliss Exp $
SYNOPSIS
use Paranoid::Network::IPv4;
@net = ipv4NetConvert($netAddr);
$rv = ipv4NetIntersect($net1, $net2);
or
use Paranoid::Network::IPv4 qw(:all);
print "Valid IP address
" if $netAddr =~ /^@{[ IPV4REGEX ]}$/;
@net = ipv4NetConvert($netAddr);
$broadcast = $net[IPV4BRDCST];
DESCRIPTION
This module contains a few convenience functions for working with IPv4 addresses.
By default only the subroutines themselves are imported. Requesting :all will also import the constants as well.
SUBROUTINES /METHODS
ipv4NetConvert
@net = ipv4NetConvert($netAddr);
This function takes an IPv4 network address in string format and converts it into an array containing the base network address, the
broadcast address, and the netmask, in integer format. The network address can have the netmask in either CIDR format or dotted quads.
In the case of a single IP address, the array with only have one element, that of the IP in integer format.
Passing any argument to this function that is not a string representation of an IP address (including undef values) will cause this
function to return an empty array.
ipv4NetIntersect
$rv = ipv4NetIntersect($net1, $net2);
This function tests whether an IP or subnet intersects with another IP or subnet. The return value is essentially boolean, but the true
value can vary to indicate which is a subset of the other:
-1: destination range encompasses target range
0: both ranges do not intersect at all
1: target range encompasses destination range
The function handles the same string formats as ipv4NetConvert, but will allow you to test single IPs in integer format as well.
CONSTANTS
These are only imported if explicity requested or with the :all tag.
MAXIPV4CIDR
Simply put: 32. This is the largest CIDR notation supported in IPv4.
IPV4REGEX
Regular expression: qr/(?:d{1,3}.){3}d{1,3}/sm
You can use this for validating IP addresses as such:
$ip =~ m#^@{[ IPV4REGEX ]}$#;
or to extract potential IPs from extraneous text:
(@ips) = ( $string =~ m#(@{[ IPV4REGEX ]})#gsm);
IPV4CIDRRGX
Regular expression:
qr#(@{[ IPV4REGEX ]})(?:/(d+|@{[ IPV4REGEX ]}))?#sm
By default this will extract an IP or CIDR notation network address:
($net, $mask) = ( $ip =~ m#^@{[ IPV4CIDRRGX ]}$# );
In the case of a simple IP address $mask will be undefined.
IPV4BASE
This is the ordinal index of the base network address as returned by ipv4NetConvert.
IPV4BRDCST
This is the ordinal index of the broadcast address as returned by ipv4NetConvert.
IPV4MASK
This is the ordinal index of the network mask as returned by ipv4NetConvert.
DEPENDENCIES
o Paranoid
o Paranoid::Network::Socket
BUGS AND LIMITATIONS AUTHOR
Arthur Corliss (corliss@digitalmages.com)
LICENSE AND COPYRIGHT
This software is licensed under the same terms as Perl, itself. Please see http://dev.perl.org/licenses/ for more information.
(c) 2012, Arthur Corliss (corliss@digitalmages.com)
perl v5.14.2 2012-05-29 Paranoid::Network::IPv4(3pm)