10-30-2019
Perfectly normal.
When you unplug the PS, a fault is generated.
You can clear the fault, after you plugged it back in and it shows everything is ok.
Regards
Peasant.
This User Gave Thanks to Peasant For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
Hello
We have a power supply in an x4100 (x86) and it seems to be faulty but it is still working!?! (this box only has one PSU). We are getting Orange flashing warning light on the front of the box and the LED labelled “rear PSu” is solid orange ...We don't seem to have had any syslog error... (8 Replies)
Discussion started by: hcclnoodles
8 Replies
2. AIX
Hi Experts,
I have configured A D40 Array. There is an faulty disk which is not part of an raid volume but shows fault in the diagnostics.
pdisk15 U0.1-P1-I1/Q1-W40AA83CC2400D
SSA160 Physical Disk Drive ( MB)
Is there a way to stop this... (2 Replies)
Discussion started by: vuppala360
2 Replies
3. Solaris
Hi All,
I replace a sub-mirror of a mirrored volume by using below command:
#metadetach d10(mirror) d11(striped)
#metattach d10 d13(other striped)
With above process I successfully replaced a faulty volume. I want to knoow if the process I followed is right. Or if not, what... (5 Replies)
Discussion started by: naw_deepak
5 Replies
4. Solaris
Hi everyone,
I wanted to ask a question about fmadm and explorer outputs.
Recently found out that an error shows up in fmadm saying "mb is faulty but still in service" so we took an explorer send to Oracle Support. Error led wasn't on but we didn't want to risk the probability.
They came up... (1 Reply)
Discussion started by: royalliege
1 Replies
5. Solaris
Hi,
Recently i came across a disk that seems to be faulty and need help. I have gathered some information by running below commands and any help on how to solve this will be great.
# uname –a
SunOS XYZ 5.7 Generic_106541-16 sun4u sparc SUNW,Ultra-4
#df -k
Filesystem kbytes used... (3 Replies)
Discussion started by: phanidhar6039
3 Replies
6. HP-UX
Hi,
Have mirrored the primary disk to 3 .
Server and OS:
# uname -a
HP-UX pdwp1s B.11.11 U 9000/800 118434630 unlimited-user license
# model
9000/800/L3000-7x
# strings /etc/lvmtab
/dev/vg00
+F@<
/dev/dsk/c1t2d0
/dev/dsk/c2t2d0
/dev/dsk/c2t0d0
But now I have only 1 disk... (5 Replies)
Discussion started by: Shirishlnx
5 Replies
7. HP-UX
Hello,
I'm new to this forum and as you will see from my question I'm new to UNIX as well.
One of our costumers has HP rx4640 running on UNIX with two 300GB hot-swappable disks that are mirrored. They reported to us that one of the disks is faulty and they want us to take care of it. Below is... (16 Replies)
Discussion started by: gjk
16 Replies
8. Solaris
Hi,
I'm trying to generate an alert related to Power Supply Failure.
As its difficult to generate such an event, Is it possible to set the status of a Power Supply Unit as "Faulty"
Any ideas are welcome and highly appreciated
-Thanks (3 Replies)
Discussion started by: justsam
3 Replies
9. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
10. Hardware
Hello,
Following parts need to be replaced in a frame as suggested by IBM
1. Flexible Cable
2. Service Processor Card
Would these faulty parts impact all lpars which are there in this frame?
Best regards,
Vishal (5 Replies)
Discussion started by: admin_db
5 Replies
LEARN ABOUT DEBIAN
kumoctl
KUMOCTL(1) General Commands Manual KUMOCTL(1)
NAME
kumoctl - show kumofs status
SYNOPSIS
kumoctl address[:port=19750] command [options]
DESCRIPTION
Show status of kumo-manager and send control commands to kumo-manager.
COMMANDS
status show status of the cluster
attach attach all new servers and start replace
attach-noreplace
attach all new servers
detach detach all fault servers and start replace
detach-noreplace
detach all fault servers
replace
start replace without attach/detach
full-replace
start full-replace (repair consistency)
backup [suffix=20090304]
create backup with specified suffix
enable-auto-replace
enable auto replace
disable-auto-replace
disable auto replace
STATUS
hash space timestamp
The time that the list of attached kumo-servers is updated. It is updated when new kumo-server is added or existing kumo-server is
down.
attached node
The list of attached kumo-servers. (active) is normal node and (fault) is fault node or recoverd but not re-attached node.
not attached node
The list of recognized but not-attached nodes.
AUTO REPLACING
By default, you have to attach new kumo-servers manually using kumoctl command. If the auto replacing is enabled, new kumo-servers are
attached automatically. This is experimental feature.
EXAMPLE
$ kumoctl mgr1 status
$ kumoctl mgr1 attach
SEE ALSO
kumo-manager(1).
kumoctl July 2009 KUMOCTL(1)