I don't know about the Ultra-30 but maybe it should be
That you can set on the firmware prompt with
Perhaps you have an exotic or too new graphics hardware that is not recognized by the firmware? Then an update of the openboot firmware might help.
Hello everybody,
I installed sun solaris i86 , the programme installation install the
"Mini Root" and after that he doing shutdown.
the camputer coming up and he can't boot.
how i can to resuled this problem ???
Thenk you in advence..... (2 Replies)
Hi,
I have a sun ultra enterprise 450 server. This server powers on and a white screen appears with the system and network information.
But it doesnot boot up completely. Booting operation wil be halted by a warning:
\usr\sbin\fsck not found. Most likely the mount of \usr failed or the... (5 Replies)
Hello
I have install new NIC ,that's RTL8139 in SUN U10 but it not work (or not detect I don't know :p)
in "ifconfig -a" it show only lo0 and hme0
in "ifconfig hme1 plumb" it show
SIOCSLIFNAME for ip: hme1 :no such interface
and there's some file that I change
/ect/hosts
... (4 Replies)
Newbie question.
I've been running OpenSolaris on an Intel box for some time with great success.
I have just bought an old Sun Blade workstation with a corrupted version of Solaris 5 something on it.
The plan was to install OpenSolaris on it.
However beyond my skills, I see, as no Live CD (or... (10 Replies)
Hi All
I have a problem on T2000 server.
bash-3.00# uname -a
SunOS 5.10 aaa Generic_120011-14 sun4v sparc SUNW,Netra-T2000After the initial solaris installation server failed to boot:
Rebooting with command: boot
Boot device: disk:b File and args:
The file just loaded does not appear... (1 Reply)
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Folks;
My SUN Ultra 10 5.9 won't boot. It only stops after counting the memory on the white screen then hangs there with nothing. even the power button won't take it down from there, i had to unplug it then re-plug it again.
i inserted a disk with Solaris 9 iso trying to rebuild it but nothing... (1 Reply)
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Hi all!
I have a Sun JavaStation-1 which doesn't boot: when I turn on the power switch, the power led becomes lit but the screen remains black (going in power save after about 5 seconds). :eek:
Now my question is: could be this problem due to a dead IDPROM? :confused:
I have this doubt because... (0 Replies)
Hi all,
I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET
Thanks,
Rob (3 Replies)
Discussion started by: robbo007
3 Replies
LEARN ABOUT LINUX
ipwfw
IPWFW(4) BSD Kernel Interfaces Manual IPWFW(4)NAME
ipwfw -- Firmware Module for Intel PRO/Wireless 2100 driver
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device ipwfw
This will include three firmware images inside the kernel. If you want to pick only the firmware image for the mode you want to operate your
network adapter in choose one of the following:
device ipwbssfw
device ipwibssfw
device ipwmonitorfw
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
ipw_bss_load="YES"
ipw_ibss_load="YES"
ipw_monitor_load="YES"
DESCRIPTION
This module provides access to firmware sets for the Intel PRO/Wireless 2100 series of IEEE 802.11 adapters. It may be statically linked
into the kernel, or loaded as a module.
For the loaded firmware to be enabled for use the license at /usr/share/doc/legal/intel_ipw/LICENSE must be agreed to by adding the following
line to loader.conf(5):
legal.intel_ipw.license_ack=1
FILES
/usr/share/doc/legal/intel_ipw/LICENSE ipwfw firmware license
SEE ALSO ipw(4), firmware(9)BSD January 14, 2010 BSD