09-23-2019
Hi,
This would indicate that the server was already connected to the SAN and that the command has been run to stop the system displaying multiple paths for each device, normally the first time you run stsmbooyt a reboot is required.
Regards
Gull04
8 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
I havent done this before but iam trying to create an image of a mirrorred drive.
Correct me if iam wrong, but when i have two disks setup in raid configuration and have them mirrored in solaris. It then defines at one entity.
How would i create a "flar" image of that one entity... (3 Replies)
Discussion started by: tlee
3 Replies
2. Linux
Hi all,
Currently i am involved in developing a device driver for a custom hardware.
My linux stack already has the sysfs directory structure
/sys/class/hwmon/
My need is that, while loading my device driver i need to create a "xyz" sysfs directory inside hwmon sysfs directory as... (0 Replies)
Discussion started by: cbalu
0 Replies
3. Red Hat
I have an HP blade with Qlogic HBA's connected to an EVA8000. I have downloaded the latest multipath.conf from HP's website. The drive presented to the server appears to be configured and working except the output of "multipath -l" shows for all paths. What is causing this output?
mpath0... (2 Replies)
Discussion started by: manzier
2 Replies
4. Linux
hello
my centOS newly installed system loading dmraid modules on startup
I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there
and he says: no raid disks found
also I did modprobe -r dm_raid45 and it do remove it but only until... (7 Replies)
Discussion started by: tip78
7 Replies
5. Red Hat
Hi,
How to find the raw device/multipath details of the LUN used by the diskgroups of the database.
file system type -- ASM
Oracle -- 11.2.0.3.0
OS -- Linux
This is RAC database.
Regards,
Maddy (2 Replies)
Discussion started by: Maddy123
2 Replies
6. Linux
Hi all
I have a system running:
uname -o
GNU/Linux
that has already some file systems created:
df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/vg_outsystemdb-lv_root
50G 2.7G 45G 6% /
tmpfs 28G 72K 28G 1%... (5 Replies)
Discussion started by: fretagi
5 Replies
7. HP-UX
Hi,
Unable to make tape backup, please help.
/opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00
* Creating local directories for configuration files and archive.
======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery.
(Mon... (4 Replies)
Discussion started by: anuragr
4 Replies
8. Red Hat
Hi,
I am testing on iSCSI + multipath, where i have one iSCSI lun assigned to one server.
mpatha (1IET 00010001) dm-2 IET,VIRTUAL-DISK
size=100M features='0' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=1 status=active
| `- 2:0:0:1 sda 8:0 active ready running
`-+-... (6 Replies)
Discussion started by: linux.amrit
6 Replies
aseqnet(1) General Commands Manual aseqnet(1)
NAME
aseqnet - ALSA sequencer connectors over network
SYNOPSIS
aseqnet [remotehost]
DESCRIPTION
aseqnet is an ALSA sequencer client which sends and receives event packets over network. Suppose two hosts connected by network, hostA as
a server and hostB as a client. The ALSA sequencer system must be running on both hosts. For creating the server port, run the following
on hostA:
hostA% aseqnet
sequencer opened: 128:0
Then a user client 128 with port 0 was opened on hostA. (The client number may vary.) For creating the (network-)client port, run aseqnet
with the hostname of the server:
hostB% aseqnet hostA
sequencer opened: 132:0
Now all events sent to hostA:128:0 are transferred to hostB:132:0, and vice versa.
The ports created by aseqnet can be connected arbitrary to other sequencer ports via aconnect(1). For example, to connect hostB:132:0 to a
MIDI output device 65:0:
hostB% aconnect 132:0 65:0
Then events to hostA:128:0 will be delivered to hostB:65:0. The following command plays MIDI on hostB.
hostA% pmidi -p 128:0 foo.mid
The multiple clients may exist simultaneously. If hostC is connected as a client to hostA, events from from hostA are sent to all con-
nected network clients, i.e. hostB and hostC. However, only one connection is allowed from a client to a server.
To disconnect network, stop all clients before server by ctrl-C or sending signal to them. The server will automatically quit.
OPTIONS
-p port
Specify the TCP port number or TCP service name.
-s addr
Subscribe to the given address for read automatically.
-d addr
Subscribe to the given address for write automatically.
-v Verbose mode.
SEE ALSO
aconnect(1), pmidi(1)
AUTHOR
Takashi Iwai <tiwai@suse.de>.
January 1, 2000 aseqnet(1)