Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
hello guys,
I have a file like this:
input.dat
Push-to-talk
No
Coonection
IP support
Support for IP telephony
Yes
Built-in SIP stack
Yes
Support via software
Yes
Microsoft
Support for Microsoft Exchange
Yes
UMA (5 Replies)
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
I'm trying to figure out what circumstances would cause an Open Solaris 11.2 host to switch itself from a static to a DHCP ip address upon reboot. This has only happened once but is a cause for some concern as this machine will be part of a web server pool.
Nothing has changed on the LAN that... (2 Replies)
Having given up for the time being with a very difficult game engine project to virtualizing cyberspace, am working on the forums again.
Just updated a few icons on the mobile site. Explanations in the picture captions:
https://www.unix.com/members/1-albums214-picture855.jpeg
... (1 Reply)
Hey,
I have enable post thanks (viewing thanks, not yet giving thanks) in mobile:
https://www.unix.com/members/1-albums214-picture1018.jpeg
I plan to also add the button to "give thanks on mobile.
In addition, I will change the formatting (color and justification) of this new mobile... (1 Reply)
Discussion started by: Neo
1 Replies
LEARN ABOUT DEBIAN
funcombine
funcombine(7) SAORD Documentation funcombine(7)NAME
FunCombine - Combining Region and Table Filters
SYNOPSIS
This document discusses the conventions for combining region and table filters, especially with regards to the comma operator.
DESCRIPTION
Comma Conventions
Filter specifications consist of a series of boolean expressions, separated by commas. These expressions can be table filters, spatial
region filters, or combinations thereof. Unfortunately, common usage requires that the comma operator must act differently in different
situations. Therefore, while its use is intuitive in most cases, commas can be a source of confusion.
According to long-standing usage in IRAF, when a comma separates two table filters, it takes on the meaning of a boolean and. Thus:
foo.fits[pha==1,pi==2]
is equivalent to:
foo.fits[pha==1 && pi==2]
When a comma separates two spatial region filters, however, it has traditionally taken on the meaning of a boolean or. Thus:
foo.fits[circle(10,10,3),ellipse(20,20,8,5)]
is equivalent to:
foo.fits[circle(10,10,3) || ellipse(20,20,8,5)]
(except that in the former case, each region is given a unique id in programs such as funcnts).
Region and table filters can be combined:
foo.fits[circle(10,10,3),pi=1:5]
or even:
foo.fits[pha==1&&circle(10,10,3),pi==2&&ellipse(20,20,8,5)]
In these cases, it is not obvious whether the command should utilize an or or and operator. We therefore arbitrarily chose to implement the
following rule:
o if both expressions contain a region, the operator used is or.
o if one (or both) expression(s) does not contain a region, the operator used is and.
This rule handles the cases of pure regions and pure column filters properly. It unambiguously assigns the boolean and to all mixed cases.
Thus:
foo.fits[circle(10,10,3),pi=1:5]
and
foo.fits[pi=1:5,circle(10,10,3)]
both are equivalent to:
foo.fits[circle(10,10,3) && pi=1:5]
[NB: This arbitrary rule replaces the previous arbitrary rule (pre-funtools 1.2.3) which stated:
o if the 2nd expression contains a region, the operator used is or.
o if the 2nd expression does not contain a region, the operator used is and.
In that scenario, the or operator was implied by:
pha==4,circle 5 5 1
while the and operator was implied by
circle 5 5 1,pha==4
Experience showed that this non-commutative treatment of the comma operator was confusing and led to unexpected results.]
The comma rule must be considered provisional: comments and complaints are welcome to help clarify the matter. Better still, we recommend
that the comma operator be avoided in such cases in favor of an explicit boolean operator.
SEE ALSO
See funtools(7) for a list of Funtools help pages
version 1.4.2 January 2, 2008 funcombine(7)