09-06-2019
Is it a production / continuity problem if you simply clear by rebooting the server?
9 More Discussions You Might Find Interesting
1. Solaris
Hello All,
I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
Discussion started by: mainegeek
10 Replies
2. Solaris
Does Veritas Cluster work with IPMP on Solaris 10?
If anyone has set it up do you have a doc or tips?
I have heard several different statements ranging from , not working at all to Yes it works! Great How?
* Test and Base IPs????
* configure the MultiNICB agent ?
I can give details... (1 Reply)
Discussion started by: dfezz1
1 Replies
3. Solaris
A problem happened with me, I was configuring IP for two network interfaces, and when I rebooted the system, everything is working but after like 3 or 5 minutes it will tell me that the whole IPMP group has failed !
I tried to troubleshoot, so I found that the gateway is not reachable..so I... (4 Replies)
Discussion started by: Sun Fire
4 Replies
4. Solaris
Hi friends ,
can anyone provide me the complete steps to configure IPMP in solaris 9 or 10 provided i have two NIC card ?
regards
jagan (4 Replies)
Discussion started by: jaganblore
4 Replies
5. Solaris
Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated...
Thanks in Advance
vks (2 Replies)
Discussion started by: vks47
2 Replies
6. Solaris
All.
I am trying to create a 10 branded zone on a Sol 11.1 T5. The Global is using IPMP...so aggregating is out of the question. Has anyone successfully created a branded zone with IPMP? If they have can you please show me the steps you took to get this to run.
Thanks (4 Replies)
Discussion started by: aeroforce
4 Replies
7. Solaris
hi all,
i start with solaris 11 and i am disapointed by the change on ip managing.
i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande
switch1
net0 aggregate1 |
net1 aggregate1 |-----|
|... (1 Reply)
Discussion started by: sylvain
1 Replies
8. Solaris
Hi all,
I been reading examples of how to setup IPMP and how it differs from Etherchannel. However, i am still unsure of how it really works and i hope gurus here can shed some light on the questions I have below while i will lab it up for my own test ->
q1) for IPMP, there is no such thing... (23 Replies)
Discussion started by: javanoob
23 Replies
9. Solaris
Hi all,
Just a few questions ->
Is an "OFFLINE" interface going back to "ONLINE" consider as a failback by IPMP ?
I have "FAILBACK=no" in my /etc/default/mpathd; however when i do the following
(igb0 and igb7 are in the same ipmp link based group)
q1) why does "if_mpadm -r igb7" cause... (0 Replies)
Discussion started by: javanoob
0 Replies
LEARN ABOUT SUSE
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)
NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <erezz@voltaire.com>.
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)