To answer your second question as far as I recall the hard disk root filesystem is /dev/root (with one r) BUT if you are mounting the hard disk root filesystem having booted from removable media (DVD/CD or floppy) to a mount point (e.g. /mnt) then it is /dev/hd0root.
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Hello
I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller .
The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver)
What ... (3 Replies)
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Hi
I hope this is the right forum.
I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller.
I need a driver for this. Can anybody point me to a download?
Thanks in anticipation. (12 Replies)
Discussion started by: Stuart1946
12 Replies
LEARN ABOUT FREEBSD
msdos
MSDOSFS(5) BSD File Formats Manual MSDOSFS(5)NAME
msdosfs -- MS-DOS file system
SYNOPSIS
options MSDOSFS
DESCRIPTION
The msdosfs driver will permit the FreeBSD kernel to read and write MS-DOS based file systems.
The most common usage follows:
mount -t msdosfs /dev/ada0sN /mnt
where N is the partition number and /mnt is a mount point. Some users tend to create a /dos directory for msdosfs mount points. This helps
to keep better track of the file system, and make it more easily accessible.
It is possible to define an entry in /etc/fstab that looks similar to:
/dev/ada0sN /dos msdosfs rw 0 0
This will mount an MS-DOS based partition at the /dos mount point during system boot. Using /mnt as a permanent mount point is not advised
as its intention has always been to be a temporary mount point for floppy and ZIP disks. See hier(7) for more information on FreeBSD direc-
tory layout.
SEE ALSO mount(2), unmount(2), mount(8), mount_msdosfs(8), umount(8)AUTHORS
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org>.
BSD October 1, 2013 BSD