07-25-2019
SCO OS 6 Driver for LSIL SAS1064E Raid Controller
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to a shell, but I can't mount the HD or the RAID, because the root fs is on a LSI Logic Raid controller MPT SAS1064E.
I found an LSIL driver for SCO OS 5.0.7 that I can load at boot time, but this version does not support this SAS RAID controller card.
Is there a driver for OS Server 5.07 for this LSIL SAS1064E RAID controller?
Or, is there a driver for OS 6.0 or for another version for SAS1064E and where can I find a boot load driver disk?
(Since it is installed and running on that box, there must be a driver somewhere!)
What device will the root filesystem be available, mounted to? (On regular startup it is at /dev/rroot)
Any help appreciated,
Thomas.
10 More Discussions You Might Find Interesting
1. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
2. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
3. Solaris
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies
4. Hardware
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Discussion started by: ranjansukumar
1 Replies
5. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
6. AIX
Hello folks,
Could someone tell me why I unable to create pdisks for a RAID Array
# lscfg | grep scsi
+ sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter
+ scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies
7. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
8. SCO
Hello
I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller .
The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver)
What ... (3 Replies)
Discussion started by: flako
3 Replies
9. Red Hat
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies
10. SCO
Hi
I hope this is the right forum.
I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller.
I need a driver for this. Can anybody point me to a download?
Thanks in anticipation. (12 Replies)
Discussion started by: Stuart1946
12 Replies
LEARN ABOUT OPENSOLARIS
ahci
ahci(7D) Devices ahci(7D)
NAME
ahci - Advanced Host Controller Interface SATA controller driver
SYNOPSIS
sata@unit-address
DESCRIPTION
The ahci driver is a SATA framework-compliant HBA driver that supports SATA HBA controllers that are compatible with the Advanced Host Con-
troller Interface 1.0 specification. AHCI is an Intel-developed protocol that describes the register-level interface for host controllers
for serial ATA 1.0a and Serial ATA II. The AHCI 1.0 specification describes the interface between the system software and the host con-
troller hardware.
The ahci driver currently supports the Intel ICH6/7/8/9, VIA vt8251 and JMicron AHCI controllers which are compliant with the Advanced Host
Controller Interface 1.0 specification. Note that while the Intel ICH6/7/8/9, VIA vt8251 and JMicron AHCI controllers support standard
SATA features, the ahci driver currently only supports hard disk, ATAPI SATA DVD, hotplug and NCQ (Native command queuing). Port multiplier
and power management are not yet supported.
CONFIGURATION
The ahci module contains no user configurable parameters.
FILES
/kernel/drv/ahci
32-bit ELF kernel module (x86).
/kernel/drv/amd64/ahci
64-bit ELF kernel module (x86).
ATTRIBUTES
See attributes(5) for descriptions of the following attribute:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWahci |
+-----------------------------+-----------------------------+
SEE ALSO
cfgadm(1M), cfgadm_sata(1M), prtconf(1M), sata(7D)
Advanced Host Controller Interface 1.0
Writing Device Drivers
NOTES
To bind the ahci driver to your controller, choose the [AHCI] BIOS option.
Note that booting is not supported if toggle exists between the [IDE] and [AHCI] BIOS options
SunOS 5.11 22 Jan 2008 ahci(7D)