1.I was trying to use Exceed to run Solaris "openwin" on my Windows 95. I got an error :
/usr/openwin/bin/openwin &
28522
$
/dev/fb: No such file or directory
Graphics Adapter device /dev/fb is of unknown type
Fatal server error:
InitOutput: Error loading module for /dev/fb
Does... (1 Reply)
I have a server that is on solaris 9 and openwin is locked. The mouse won't respond and I can't seem to kill the openwin pid on the server.. Is there a command line to kill openwin from the server side? (2 Replies)
Discussion started by: jphorton
2 Replies
3. Post Here to Contact Site Administrators and Moderators
Hi Gents,
I have downloaded Sol 8 2/04 from Sun's web page and I have tried to install it into a V890. I can boot from a CD 1of 2 without any problem.
After the selection of the language and the Locale, the TWM (Sol Install Console window) cannot starts up. The following are the errors... (0 Replies)
Hi all,
I am a newbies here,
Have question regards large hard disk install in SunBlade system.
Can SunBlade 150 support 2 x 160GB (internal IDE) ?
Want to make sure before buy the hard disks.
Anyone had experiences configure large hard disk in SunBlade 150 before ?
In the SunBlade 150... (2 Replies)
I have a client who is using Solaris 8 and on login the system tris to open windows but then generates the following error
failed to open /usr/openwin/AcceleratedX/etc/Siteinfo
Fatal Server error
Failed to configure the xserver
Help Please!
Thanks (0 Replies)
Solaris 10 on an Ultra 45, there are two serial ports (com A and B) And I need to be able to use an old serial trackball mouse in the openwin dt enviornment. Do I have any options? Even if I have to buy an external device for conversion? Want to configure openwin to use an old serial pointer device... (0 Replies)
I purchased a Sunblade 150 from Ebay. It had 512MB RAM and 80GB hard disk. I recently purchased additional RAM and another 80GB disk, and installed them. The RAM goes through POST without issues. I just can't get beyond the OK prompt. I am using the serial console.
I have been unable to... (5 Replies)
I have several applications locked to Solaris 8 (and older) and have been very happy with my Sparcs and Ultras but am getting tinnitus problems from fans and disks.
Any tips on a quiet thin client (with decent graphics, not video or gaming level but 24bit and multi monitor would be useful) that... (0 Replies)
Discussion started by: batchman
0 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)