06-01-2019
Please do not cut-and-paste post from stack exchange (or any other site), unformatted, here at unix.com.
It's OK to post at multiple locations on the net, but just cutting and pasting from one site without any regard for formatting or the site, is really not nice.
This is an unformatted (forum pollution) version of a post on stack exchange posted today by "greenelephant".
In fact, it's not clear to me if "these are your posts" or if you are just "cutting and pasting others posts"....
Either way...
Thread closed.
8 More Discussions You Might Find Interesting
1. HP-UX
Hi.
I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card... (1 Reply)
Discussion started by: wobitu
1 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
4. IP Networking
Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten
Unable to get NIC working
Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)
Discussion started by: lindab
0 Replies
5. UNIX for Dummies Questions & Answers
Hi Gurus
can I emulate solaris/sparc on virtualbox? Or other emulator to run solaris for sparc in my win7 PC?
regards,
Israel. (9 Replies)
Discussion started by: iga3725
9 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
8. UNIX for Beginners Questions & Answers
I have a Oracle SPARC server with Solaris SPARC 10 OS installed
I have a domestic router/modem box from my ISP in my house. I have a wifi extender in my room which has a RJ45 female socket for ethernet connection. The Wifi extender is configured properly to act as a bridge for machines to... (5 Replies)
Discussion started by: alphatron150
5 Replies
LEARN ABOUT DEBIAN
blaze-remove
BLAZE-REMOVE(1) BlazeBlogger Documentation BLAZE-REMOVE(1)
NAME
blaze-remove - removes a post or page from the BlazeBlogger repository
SYNOPSIS
blaze-remove [-fipqPV] [-b directory] id...
blaze-remove -h|-v
DESCRIPTION
blaze-remove removes a blog post or a page with the specified id from the BlazeBlogger repository.
OPTIONS
-b directory, --blogdir directory
Allows you to specify a directory in which the BlazeBlogger repository is placed. The default option is a current working directory.
-p, --page, --pages
Tells blaze-remove to remove a page or pages.
-P, --post, --posts
Tells blaze-remove to remove a blog post or blog posts. This is the default option.
-f, --force
Disables requiring manual confirmation of each blog post or page removal. This is the default option.
-i, --interactive
Enables requiring manual confirmation of each blog post or page removal.
-q, --quiet
Disables displaying of unnecessary messages.
-V, --verbose
Enables displaying of all messages. This is the default option.
-h, --help
Displays usage information and exits.
-v, --version
Displays version information and exits.
EXAMPLE USAGE
Remove a blog post:
~]$ blaze-remove 10
Successfully removed the post with ID 10.
Remove a page:
~]$ blaze-remove -p 4
Successfully removed the page with ID 4.
Remove multiple blog posts:
~]$ blaze-remove 10 4 6
Successfully removed the post with ID 10, 4 and 6.
Remove multiple blog posts safely:
~]$ blaze-remove -i 10 4 6
Remove the post with ID 10 titled `Debian and Fedora Packages'? y
Remove the post with ID 4 titled `BlazeBlogger 0.8.0 RC2'? y
Remove the post with ID 6 titled `BlazeBlogger 0.8.1'? y
Successfully removed the post with ID 10, 4 and 6.
SEE ALSO
blaze-config(1), blaze-add(1), blaze-list(1)
BUGS
To report a bug or to send a patch, please, add a new issue to the bug tracker at <http://code.google.com/p/blazeblogger/issues/>, or visit
the discussion group at <http://groups.google.com/group/blazeblogger/>.
COPYRIGHT
Copyright (C) 2008-2011 Jaromir Hradilek
This program is free software; see the source for copying conditions. It is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Version 1.2.0 2012-03-05 BLAZE-REMOVE(1)