04-08-2019
Pinned system memory growing constantly
Hi,
Pre data: a server running AIX 6.1 TL9 with 2GB memory and a small amount of CPU, running a very light workload.
I have a server which crashed on lack of memory. After the crash I found - using nmon analyser - that there was something eating up memory. Nmon referred to it as "system".
Now, after 2 days of uptime I see that the same "someting" is eating up memory again. I've been using nmon, vmstat and svmon to see what is happening, but all I see is that
- - all user process is using the same amount of memory
- - vmstat shows a steady decrease on free list
- - svmon -G shows the same steady amount of memory being pinned
- - svmon -P shows that there is no change of pinned memory usage in the listed processes
The rate of memory loss is about 0.5% in every hour.
So I assume that some kernel related object is accumulating the pinned memory.
Can you please help me to find out the problematic part?
Additional info: there was a reported bug in AIX7.2 which have been corrected in an update. But: this machine was running for a while without any problems.
--Trifo
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Can you please tell me how to find out System Memory (RAM) for a AIX unix server?
The command prtconf will do for Solaris but I don't know for AIX Unix. (1 Reply)
Discussion started by: anilkumar
1 Replies
2. SCO
In the sco unix ,how can i get the system information ?
such as cpu,memory,interrupter,io ports etc
look forword to quick replay (2 Replies)
Discussion started by: fresh
2 Replies
3. UNIX for Dummies Questions & Answers
Hello all
im working on sunos machine that dont have the top installed and can't be
install , now i need to get information similar to what top gives me about the cpu usage and so
can it be done somehow else where ? (3 Replies)
Discussion started by: umen
3 Replies
4. Programming
Dear all,
When I write the daemon programs it is consuming high memory and processor time. How can I avoid this?
But, the system daemons are not consuming more. How?
Can any one explain how the system daemons are handling the memory consumption and processor time.
Thanks,... (1 Reply)
Discussion started by: nagalenoj
1 Replies
5. UNIX for Advanced & Expert Users
It is a little bit weird to me when i found this on a solaris 9 system with openssh package. Below is the result copied from "top" output:
PID USERNAME LWP PRI NICE SIZE RES STATE TIME CPU COMMAND
13491 root 1 59 0 27M 18M sleep 0:06 0.00% sshd -i
20198 root ... (1 Reply)
Discussion started by: sleepy_11
1 Replies
6. HP-UX
Hello, I noticed very high system memory utilization on my new 11.31 Itanium systems. System memory is more than 11GB on 32 GB system. Comparing this to 11.23 it's more than double ... How do I find out what is using it? Is there a way to reduce it?
Thank you,
Kubo (4 Replies)
Discussion started by: trunecm1
4 Replies
7. Solaris
Hi gurus
Im a newbie in solaris..I need to extend file system space in solaris 10 which is using SVM..I have a file system /pin02 which is 93% full n needs to be extended..only 3.6 gb avail space left..the file system is not mirrored...normal ufs file system only..can u please tel me t... (6 Replies)
Discussion started by: madanmeer
6 Replies
8. Shell Programming and Scripting
I am working on a server where the 'root' user ZFS filesystem.
Now when I do Top commands it says only 750M free .But when I count the actual memory utilized it comes only to 12 GB and the total size of the server is 32G.
I think rest of the space is held up by ZFS file system.
Is there a... (5 Replies)
Discussion started by: prasperl
5 Replies
9. AIX
I already checked memory on AIX with "svmon -G" and vmstat (as the figure). I see the value "inuse" nearly=97% use memory, free=3%. However, the value "pin=cache" nearly=26%.
Can I calculate total free memory= free+ pin = 29% ?
please help me!
Thanks so much! (5 Replies)
Discussion started by: xuanthanhnk
5 Replies
10. Linux
Hey everyone. Ok, so I know that from inside of any particular program, it see's through virtualized memory, a full range of available memory. It is given the ability then to place variables, data, user input etc, on the Stack, Heap, BSS, or Code segment of it's range. My question is what does the... (5 Replies)
Discussion started by: Lost in Cyberia
5 Replies
LEARN ABOUT REDHAT
netdump-server
NETDUMP-SERVER(8) System Programs NETDUMP-SERVER(8)
NAME
netdump-server - handle crash dumps over the network
SYNOPSIS
netdump-server [--port portnumber]
[--concurrent number]
[--pidfile path]
[--daemon]
[--help] [--usage]
DESCRIPTION
Listens to the network for clients that crashes and uses the netdump protocol to recieve a memory dump and a stack trace. The memory dump
and oops message are stored in a timestamped directory in /var/crash. The server can also run scripts when some events happen.
OPTIONS
--port portnumber
Specifies the IP port number for the netdump server to listen to. The default is 6666.
--concurrent number
You can limit the amount of concurrent dumps being done at any one time. If more clients than the specified maximum connects at one
time the last ones will just be logged and then rebooted.
--pidfile path
Store a pidfile. The default service uses /var/run/ttywatch.pid. The default is not to write a pidfile.
--daemon
ttywatch should background itself and run as a daemon.
EXAMPLES
netdump-server --daemon
This launches the netdump-server and puts it in the background, listening for crashed clients.
EXIT STATUS
Exit status is 0 for a clean exit and non-0 for a non-clean exit.
FILES
/etc/netdump.conf
A configuration file read by netdump-server on startup. It is a "key=value" style file. Currently it supports the options: port,
max_concurrent_dumps, daemon and pidfile.
/etc/init.d/netdump-server
An init script to start a default system installation of netdump-server. This is normally turned off by default; use the command
/sbin/chkconfig netdump-server on
to enable the netdump-server service.
/var/crash
The main directory where the crash dump files are stored. Each dump is put in a subdirectory named with the ip of the crashed
machine and the date and time of the crash.
/var/crash/scripts
This directory can contain scripts that are run at various times. They all get passed the ip of the crashing machine as the first
argument, and each one except netdump-start gets the directory that the dump is written into as the second argument.
netdump-start - This is called when a client connects to the server to tell it that it has just started the netdump client. This
normally means that the machine just booted up.
netdump-crash - This is run when a client reports that it has crashed. If it returns a non-zero value the dump request will be
ignored and the client will be told to reboot immediately
netdump-nospace - This is run when there is not enough diskspace for the dump of the crashed machine. If this script exits with a
non-zero return value netdump-server will try once again (but only once) before giving up the dump. If this script exits with a zero
return value, netdump-server will reboot the client without performing a dump.
netdump-reboot - This is run when netdump-server is finished with a client and is about to tell the client to reboot itself.
SEE ALSO
netdump(8)
BUGS
Report any bugs you find to http://bugzilla.redhat.com/bugzilla
AUTHOR
Alexander Larsson <alexl@redhat.com>
Linux 14 Feb 2002 NETDUMP-SERVER(8)