I appreciate iif anybody can help me with this issue. I set up a Linux FTP server which is authorized user ID from AD. I do some configuration on vsftpd.conf file but it doesn't work out. I copy these configuration, can you help me to check again as when i connect through browser it always give me... (2 Replies)
Hi!
I have 2 servers. The firts has vsftpd server with this configuration:
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all... (2 Replies)
Hi,
Am running the following commands on our server to generate a key for passwordless SSH, however we are getting 100% blank key files.
E.g. when looking id_dsa.pub or id_dsa they are 100% empty - the files get created, but contain no content and have a file size of 0b.
mkdir ~/.ssh... (3 Replies)
I am writing perl script to configure Cisco device but Variables inside Net::Telnet::Cisco Module doesn't work and passed to device without resolving.
Please advise.
here is a sample of script:
use Net::Telnet::Cisco;
$device = "10.14.199.1";
($o1, $o2, $o3, $o4) = split(/\./,$device);... (5 Replies)
Hi, I have a question.
I define a function using sed command:
replace()
{
searchterm=$1
replaceterm=$2
sed -e "s/$searchterm/$replaceterm/ig" $3 > $WORK'tempfile.tmp'
mv $WORK'tempfile.tmp' $3
}
Then I call
replace 'test = 0' 'test = 1' $myfileThis code works well in... (1 Reply)
Hi, I have a question.
I define a function using sed command:
replace()
{
searchterm=$1
replaceterm=$2
sed -e "s/$searchterm/$replaceterm/ig" $3 > $WORK'tempfile.tmp'
mv $WORK'tempfile.tmp' $3
}
Then I call
replace 'test = 0' 'test = 1' $myfile
This code... (1 Reply)
Recently I decided to intall second daemon of SSH for Winbind users.
I mean I have configuration AIX + Samba + AD and I can login to the server via SSH with AD accounts to 22 port without any problems.
But now I have second installation of OpenSSH and don't understand why I can't do the same... (6 Replies)
Hello Experts,
I am performing performance tests on a few mysql select queries.
I use the following command to clear the memory disk caches.
sync && echo 3 | sudo tee /proc/sys/vm/drop_caches
I however see that the above command works on RHEL6 but doesn't work on Solaris 10.
I asked... (4 Replies)
I am sorry if i post in wrong Form.
i have AIX server in which ssh works for all users but sftp only works for root user .
it is too much important for me to solve this .
Your help will be greatly appreciated. (1 Reply)
I cant ping to some of my machines, but ping works.
I attach screenshots. Port is open and it is 22.
I can't figure out why i cant access.
https://www.unix.com/attachments/unix-for-advanced-and-expert-users/7492d1541541072-cant-ssh-but-ping-works-sshlisten-jpg... (17 Replies)
Discussion started by: tomislav91
17 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)