:confused:
Hi:
I donīt know how to add route gateway and when restart the machine lose this route and put other.
In SCO ver 5.6 Enterprise write:
etc\route delete gateway
route add gateway 199.199.1.1.
so , netstat -rn to see if has change -> all ok
Restart -> !!!... (2 Replies)
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Hello all!
We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our... (0 Replies)
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Hi all,
i have a rhel 6.2 with a default gateway.
This server is an Intranet office with no internet access.
DNS are already configured and it's possible to resolve my target.
My goal is to link my application (apache forward) only to http://mytarget.yyy through a new gateway (That does... (0 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT FREEBSD
ng_atmllc
NG_ATMLLC(4) BSD Kernel Interfaces Manual NG_ATMLLC(4)NAME
ng_atmllc -- ATM LLC netgraph node type
SYNOPSIS
#include <netgraph/ng_atmllc.h>
DESCRIPTION
The atmllc node type translates frames in to and out of ATM LLC encapsulation, as specified by RFC 1483. In LLC encapsulation the protocol
of a given protocol data unit (PDU) is specified by an IEEE 802.2 LLC header, possibly followed by an IEEE 802.1a SubNetwork Attachment Point
(SNAP) header. This node currently handles the Ethernet and FDDI protocols.
The node transmits and receives ATM PDUs on the atm hook. Received PDUs are decoded and forwarded to the ether or fddi hooks as appropriate.
Data received on the ether or fddi hooks are assumed to be full Ethernet or FDDI packets as appropriate and are encapsulated into a PDU and
transmitted via the atm hook.
HOOKS
This node type supports the following hooks:
atm ATM connection. Typically, this hook would be connected to a ng_atm(4) node, which handles transmission of ATM PDUs over an ATM
device.
ether Ethernet connection. This hook sends and receives Ethernet frames. This would normally be connected to an ng_eiface(4) node if in
use.
fddi FDDI connection. This hook sends and receives FDDI frames.
CONTROL MESSAGES
This node type supports the generic control messages.
SHUTDOWN
This node shuts down upon receipt of a NGM_SHUTDOWN control message, or when all hooks have been disconnected.
SEE ALSO netgraph(4), ng_atm(4), ng_eiface(4), ngctl(8)
J. Heinanen, Multiprotocol Encapsulation over ATM Adaptation Layer 5, RFC 1483.
AUTHORS
Benno Rice <benno@FreeBSD.org>
BSD March 8, 2004 BSD