I tried to add a route like this, however as shown an error is thrown :
The 10.132.81.161 gateway is used as a gateway for another interface in the server (eno50).
Why is the error above thrown when I try to add that line? Is it because that gateway is not initiated as a default gateway in the routing table?
:confused:
Hi:
I donīt know how to add route gateway and when restart the machine lose this route and put other.
In SCO ver 5.6 Enterprise write:
etc\route delete gateway
route add gateway 199.199.1.1.
so , netstat -rn to see if has change -> all ok
Restart -> !!!... (2 Replies)
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Hello all!
We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our... (0 Replies)
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Hi all,
i have a rhel 6.2 with a default gateway.
This server is an Intranet office with no internet access.
DNS are already configured and it's possible to resolve my target.
My goal is to link my application (apache forward) only to http://mytarget.yyy through a new gateway (That does... (0 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT SUNOS
tc-route
Route classifier in tc(8) Linux Route classifier in tc(8)NAME
route - route traffic control filter
SYNOPSIS
tc filter ... route [ from REALM | fromif TAG ] [ to REALM ] [ classid CLASSID ] [ action ACTION_SPEC ]
DESCRIPTION
Match packets based on routing table entries. This filter centers around the possibility to assign a realm to routing table entries. For
any packet to be classified by this filter, a routing table lookup is performed and the returned realm is used to decide on whether the
packet is a match or not.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
from REALM
fromif TAG
Perform source route lookups. TAG is the name of an interface which must be present on the system at the time of tc invocation.
to REALM
Match if normal (i.e., destination) routing returns the given REALM.
EXAMPLES
Consider the subnet 192.168.2.0/24 being attached to eth0:
ip route add 192.168.2.0/24 dev eth0 realm 2
The following route filter will then match packets from that subnet:
tc filter add ... route from 2 classid 1:2
and pass packets on to class 1:2.
NOTES
Due to implementation details, realm values must be in a range from 0 to 255, inclusive. Alternatively, a verbose name defined in
/etc/iproute2/rt_realms may be given instead.
SEE ALSO tc(8), ip-route(8)iproute2 21 Oct 2015 Route classifier in tc(8)