01-31-2019
Thanks.
The issue is at the Hardware BCH boot menu level. I know I posted in the HPUX OS group, didn't see a hardware forum.
I did initially have a 11.31 OS installed on the disk at intscsib.0 and it boots. IOSCAN from hpux 11.31 doesn't see the other slot/disk. The disk at intscsia.1 is a 11.11 release of HPUX.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Will some one tell me what this means.
"warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20."
I'm running SCO 505 on a proliant 1600r.
Thnank you in advance. (3 Replies)
Discussion started by: franruiz
3 Replies
2. Linux
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives... (2 Replies)
Discussion started by: tamcomng
2 Replies
3. Solaris
Version: solaris 10 x86
I just got a western digital external harddrive formated with fat 32. this drive came with some setup files which is meant for windows or mac.
I want to reformat and partition this drive into two ( for solaris and windows) such that the setup files will still be there... (2 Replies)
Discussion started by: seyiisq
2 Replies
4. Linux
Here's the story -
I installed Linux on my Y drive, and all went well until I tried to boot into XP again. I can't access or install an operating system to my other three hard drives, C, X, and Z.
I think that during the install my hard drives were changed to something other then NTFS, but... (4 Replies)
Discussion started by: Ironkey
4 Replies
5. Filesystems, Disks and Memory
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Discussion started by: Katkota
3 Replies
6. Solaris
I have a T2000 Sun-Fire server. I have 2 sets of drives in a raid 1. Lets call them Set A and Set B. I had Set A installed and working. I needed a new install so I so build up Set B. After some time I wanted to put Set A back in the server. Now the system will not boot off of Set A. I tried to boot... (7 Replies)
Discussion started by: stu1811
7 Replies
7. Hardware
Hello everyone. I have a question which I may know the answer to, I'm just looking for a confirmation. When it comes to the MBR of a hard drive, i've read in multiple sources that it's always located in the first sector of the hard drive. Is the MBR there from the factory? When I buy a new blank... (3 Replies)
Discussion started by: Lost in Cyberia
3 Replies
8. Solaris
I have three Sun Oracle Netra T5220s. I am trying to just get the processor information psrinfo or prtdiag -v from the # prompt in single user mode.
I am needing to know the commands to get to boot the CD/DVD of the Solaris OS. I am using it via Serial Port Management.
Tinkering around I... (4 Replies)
Discussion started by: nerdboy
4 Replies
9. Solaris
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Discussion started by: ssabet
5 Replies
10. UNIX for Beginners Questions & Answers
Ok so i thought i was smart but i can tell I need some help. I am playing around with understanding lvm and adding disks to a linux box. I added a disk and then ran what i thought were commands to add this disk to the box but I think I messed up and would like some help. My question is did i... (5 Replies)
Discussion started by: cptkirkh
5 Replies
diskd(1) General Commands Manual diskd(1)
Name
diskd - disk daemon; wait for disk to be inserted
Note
This manpage has been automatically generated from fdutils's texinfo documentation. However, this process is only approximative, and some
items, such as cross-references, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate rep-
resentation in the manpage format. Moreover, only the items specific to each command have been translated, and the general information
about fdutils has been dropped in the manpage version. Thus I strongly advise you to use the original texinfo doc.
* To generate a printable copy from the texinfo doc, run the following commands:
./configure; make dvi; dvips fdutils.dvi
* To generate a HTML copy, run:
./configure; make html
A pre-made HTML can be found at: `http://www.tux.org/pub/knaff/fdutils'
* To generate an info copy (browsable using emacs' info mode), run:
./configure; make info
The texinfo doc looks most pretty when printed or as HTML. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.
Description
The diskd command has the following syntax:
diskd [-d drive] [-i interval] [-e command]
Diskd waits for a disk to be inserted into a given drive, and then either executes the command or exits. This program can be used to auto-
matically mount a disk as soon as it is inserted.
Warning
This program works by switching the motor on for a very short interval, and then seeking to track -1. This might damage hardware in the
long run. Amigas, which also use these techniques, are known for having problems with their disk drives no longer spinning up properly
after a few month of usage.
Options
-d drive
Selects the drive to observe for disk insertion. By default, drive 0 (/dev/fd0) is observed.
-i interval
Selects the polling interval. The interval is given in tenths of seconds. Default is 10 (one second).
-e command
Gives the command to be executed when a disk is inserted. If no command is given the program simply exits. Typically, the command
mounts the disk. It can be a shell scripts which probes for several filesystems and disk geometries until it succeeds.
Bugs
* Automatic unmounting cannot yet be handled. It is indeed not enough to scan for disk removal, because when the disk is removed, it
is already too late: There might be some buffers needing flushing. However, the fdmountd program allows automatic unmounting by
using the SYNC mount options, which switches off write buffering (see section fdmount).
* The drive motor is running all the time, and on some computers, the drive led flickers at each time the drive is polled.
See Also
Fdutils' texinfo doc
fdutils-5.5 03Mar05 diskd(1)