SCSICTL(8)						    BSD System Manager's Manual 						SCSICTL(8)

NAME

     scsictl -- a program to manipulate SCSI devices and busses

SYNOPSIS

     scsictl device command [arg [...]]

DESCRIPTION

     scsictl allows a user or system administrator to issue commands to and otherwise control SCSI devices and busses.	It is used by specifying a
     device or bus to manipulate, the command to perform, and any arguments the command may require.  scsictl determines if the specified device
     is an actual device or a SCSI bus automatically, and selects the appropriate command set.

     For commands which scsictl issues a SCSI command to the device directly, any returned sense information will be decoded by scsictl and dis-
     played to the standard output.

DEVICE COMMANDS

     The following commands are supported for SCSI devices:

     defects [primary] [grown] [block|byte|physical]

     Read the primary and/or grown defect lists from the specified device in block, byte from index, or physical sector format.  The default is to
     return both the primary and grown defect lists in physical sector format.	This command is only supported on direct access devices.

     format [blocksize [immediate]]

     (Low level) format the named device.  If the optional blocksize parameter is provided, the device geometry will be modified to use the speci-
     fied blocksize.  If this parameter is different form the Current or Default Mode Page 3 parameters, the device will update Mode Page 3 at the
     successful completion of the Format.  Device geometry may change as a result of using a new device blocksize.  When the optional blocksize
     parameter is specified, the Defect List on the drive will revert to the original primary defect list created at the time of manufacture if
     available.  The drive will usually recertify itself during the Format and add any other defective blocks to the new Defect List.  Some disks
     may not support the ability to change the blocksize and may enter a Degraded Mode when fed a Format command of this type.	If this happens
     the standard recovery for the drive requires issuing a correct Format command, i.e. one without the blocksize parameter.

     When the immediate parameter is also specified, the disk is instructed to return from the format command right away.  It continues to format,
     and every ten seconds scsictl issues a TEST UNIT READY command to check the associated sense data.  This associated sense data has a progress
     indicator which indicates how far the format is progressing.  Note well that most SCSI disk drives prior to a few years ago do not support
     this option.

     identify

     Identify the specified device, displaying the device's SCSI bus, target, and lun, as well as the device's vendor, product, and revision
     strings.

     reassign blkno [blkno [...]]

     Issues a REASSIGN BLOCKS command to the device, adding the specified blocks to the grown defect list.  This command is only supported on
     direct access devices.

     release

     Send a ``RELEASE'' command to the device to release a reservation on it.

     reserve

     Send a ``RESERVE'' command to the device to place a reservation on it.

     reset

     Reset the device.	This command is only supported for devices which support the SCIOCRESET ioctl.

     start

     Send a ``START'' command to the device.  This is useful typically only for disk devices.

     stop

     Send a ``STOP'' command to the device.  This is useful typically only for disk devices.

     tur

     Send a ``TEST UNIT READY'' command to the device.	This is useful for generating current device status.

     getcache

     Returns basic cache parameters for the device.

     setcache none|r|w|rw [save]

     Set basic cache parameters for the device.  The cache may be disabled (none), the read cache enabled (r), the write cache enabled (w), or
     both read and write cache enabled (rw).  If the drive's cache parameters are savable, specifying save after the cache enable state will cause
     the parameters to be saved in non-volatile storage.

     flushcache

     Explicitly flushes the write cache.

     setspeed speed

     Set the highest speed that the optical drive should use for reading data.	The units are multiples of a single speed CDROM (150 KB/s).  Spec-
     ify 0 to use the drive's fastest speed.

BUS COMMANDS

     The following commands are supported for SCSI busses:

     reset

     Reset the SCSI bus.  This command is only supported if the host adapter supports the SCBUSIORESET ioctl.

     scan target lun

     Scan the SCSI bus for devices.  This is useful if a device was not connected or powered on when the system was booted.  The target and lun
     arguments specify which SCSI target and lun on the bus is to be scanned.  Either may be wildcarded by specifying the keyword ``any'' or
     ``all''.

     detach target lun

     Detach the specified device from the bus.	Useful if a device is powered down after use.  The target and lun arguments have the same meaning
     as for the scan command, and may also be wildcarded.

NOTES

     When scanning the SCSI bus, information about newly recognized devices is printed to console.  No information is printed for already probed
     devices.

FILES

     /dev/scsibus* - for commands operating on SCSI busses

SEE ALSO

     ioctl(2), cd(4), ch(4), sd(4), se(4), ss(4), st(4), uk(4), atactl(8), dkctl(8)

HISTORY

     The scsictl command first appeared in NetBSD 1.4.

AUTHORS

     The scsictl command was written by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, NASA Ames Research Center.

BSD
								 January 22, 2007							       BSD