i don't see an attachment?
you could run:
although you will have to add it to somewhere in /etc/rc2.d to have it survive a reboot. (where 192.168.1.1 is the gateway address)
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
hello guys.
I just installed SCO 5.0.6 OpenServer it went all the way to the end of the installation and the first boot try it gave me this message.
not a directory
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot (2 Replies)
Hi there guys.
I just got this new SCO version and i'm having some problem printing from shell,
This is what i'm typing at the # sign : lp -dHP /etc/hosts and it prints no problem but when i use any other user at the $ sign it gives me this error.
/dev/fd/7: /usr/lib/lp/sysv/7: not found.
... (1 Reply)
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Dear members
when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config.
i tried MP4, EFS 5.64,5.70A but not solved the problem.. (0 Replies)
Hi,
I have an openserver 5.0.0 machine in the office. The sysad of that machine left years ago without leaving the password to anyone.
I was wondering if someone has a copy of the boot / root diskettes (rescue) for this version? Or perhaps if anyone knows a download link / location in the... (0 Replies)
I need SCO Openserver 4.2. Please, give me distributive of that version SCO:eek: (0 Replies)
Discussion started by: caine
0 Replies
LEARN ABOUT FREEBSD
gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD