I am new to UNIX and have been trying to add DNS servers so I can access the internet under Solaris 9. I am using a static IP and have the subnet and gateway configured but cannot figure out to add DNS servers. Does anyone know how to do this? Thank you very much for any help. (1 Reply)
Hello evrybody
I need to know how i can implement and configure DNS server in solaris9 and i need to understand which files i modified it to do that
Thanks all (8 Replies)
hey guys, how to add soalris box as a microsoft DNS Client ?
and how to register in the microsoft DNS ??
i managed to query from the DNS server after adding /etc/resolve.conf and editing /etc/nsswitch.conf
but i need to register the soalris server (dns Client) into Microsoft DNS automatically.... (3 Replies)
Hi all,
What is the procedure to add a client to a DNS server.
what are the settings and files need to be added/changed ?
thanks in advance! (6 Replies)
Hi all,
I have some sort of problem with BIND DNS server my environment as follows.
bash-3.00# cat /etc/release
Solaris 10 6/06 s10s_u2wos_09a SPARC
Copyright 2006 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to... (3 Replies)
Hello,
I have task to make a program that multiplies polynomials as client(input/output indexes)-server(multiplying) using RPC. However when I try to compile it with gcc it gives the next info:
for client:
Udefined first
symbol referenced
Clnt_create client.o
for server:
Udefined first... (5 Replies)
Hi folks,
I am attempting to setup a Solaris 10 syslog server to receive logs from linux machines. Here's what I did:
On the server (SunOS sun226 5.10), IP address: 192.168.212.226:
1. start syslogdby issuing $/usr/sbin/syslogd -T
On a client (SunOS sun221 5.8):
1. Configured... (1 Reply)
Hi,
We have built a new server (RHEL VM)and added that IP/hostname into dns zone configs file on DNS server (Solaris 10). Reloaded the configuration using
and added nameserver into resolv.conf on client. But when I am trying nslookup, its not getting resolved. The nameserver is not able to... (8 Replies)
Discussion started by: snchaudhari2
8 Replies
LEARN ABOUT FREEBSD
gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD