11-07-2018
Thanks for the reply Hicksd8, but I did find out what I needed to do. Configuring the /etc/defaultrouter doesn't seem to work within the child zone. I had to configure the 'set defrouter=X.X.X.X' within the zone config. That enabled the default route I needed in order for the child zone to use the new network configured on the global zone. This does bring a problem though on the global zone as there is now more than one default route configured on it. Oracle don't recommend you do it this way due to this problem, but don't offer an alternative really.
We can live with that though as the global zone is only hosting child zones and nothing else. The zones seem to be working fine now.
Sparcman
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Can anybody help me on how to configure the network in Sun Solaris. This is my first time to touch sun system please help!!!:confused: :confused: (2 Replies)
Discussion started by: jameswong
2 Replies
2. Solaris
I am seeking help from the gurus in this forum and hope that I can find answers soon. Anyone who provide the answers will be greatly appreciated.
I have a sparc box with Solaris 10 on it. We install Solaris with zone structure. One global zone and two other zone. I installed Oracle DB on global... (6 Replies)
Discussion started by: duke0001
6 Replies
3. Solaris
Hi..i have installed solaris 10 on vmware. I m not able connect to internet.
pls help in detail. how to solve the problem. During the installation i have put no DHCP. cofigured manually ( Ip 192.168.1.9) default gateway 192.168.1.1 . (3 Replies)
Discussion started by: johnavery
3 Replies
4. Solaris
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
Discussion started by: newbiesolaris10
4 Replies
5. Solaris
Hi, guys, recently my os changed to solaris 10, and i want to share the printer with another computer whose os is also solaris. Is there anyone could give me a hint to fix this problem.
lpadmin -p hp5200 -v /dev/null -A write -n... (1 Reply)
Discussion started by: papertiger
1 Replies
6. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
7. Solaris
I am trying to create a branded 10 zone on a Solaris 11.1 control domain. I am using a flar image (cpio) from an existing LDOM. Here are the steps taken after flarcreate.
#zonecfg -z <device>
>create -b
>set brand=solaris10
>set zonepath=/zonez/<device>
>set ip-type=exclusive
>add net... (1 Reply)
Discussion started by: aeroforce
1 Replies
8. Solaris
Hello, I followed these instructions to create a Solaris 11 zone:
http://www.oracle.com/technetwork/articles/servers-storage-admin/o11-092-s11-zones-intro-524494.html
And I am unable to ping anything from the Local Zone except for the IP address of the global zone.
My global zone has an IP... (6 Replies)
Discussion started by: unblockable
6 Replies
9. Solaris
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
Discussion started by: Shirishlnx
0 Replies
10. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT OPENDARWIN
zprint
ZPRINT(1) General Commands Manual ZPRINT(1)
NAME
zprint - show information about kernel zones
SYNOPSIS
zprint [-w] [-s] [-c] [-h] [name]
DESCRIPTION
zprint(1) displays data about Mach zones. By default, zprint will print out information about all Mach zones. If the optional name is
specified, zprint will print information about each zone for which name is a substring of the zone's name.
zprint interprets the following options:
-w For each zone, zprint calculates how much space is allocated but not currently in use, the space wasted by the zone.
-s zprint sorts the zones, showing the wasting the most memory first.
-c (Default) zprint prints zone info in columns. Long zone names are truncated with '$', and spaces are replaced with '.', to allow
for sorting by column. Pageable and collectible zones are shown with 'P' and 'C' on the far right. Zones with preposterously large
maximum sizes are shown with '----' in the max size and max num elts fields.
-h (Default) Shows headings for the columns printed with the -c option. It may be useful to override this option when sorting by col-
umn.
Any option (including default options) can be overridden by specifying the option in upper-case; for example, -C overrides the (default)
option -c.
SEE ALSO
host_zone_info(2).
27/02/87 ZPRINT(1)