09-30-2018
Yes, DISM.
MemTotal: 16342812 kB
SwapTotal: 8000508 kB
During installation I tried various configurations, with respectively 60, 40 and 25% of RAM value for total memory, of these % 3/4 was SGA, 1/4 PGA. So for example at 60% (10 GB) it was 7,5GB SGA + 2,5GB PGA. At one point I tried to go < 1 GB total.
So you are saying I must up the SGA value to mach (or exceed) swap?
9 More Discussions You Might Find Interesting
1. Ubuntu
i trying to install hula onto my ubuntu but it seems to be not working. i follow through every instructions which i found from the net but is still not working. As i have already install allthe necessary dependency!
Below are all the dependency i have install:
debhelper (>= 4.0.0),... (0 Replies)
Discussion started by: thms_sum
0 Replies
2. Windows & DOS: Issues & Discussions
Hi ,
I hav a laptop with Vista, i need to install Ubuntu along with vista on it. But the problem is tht i donot hav a hard drive partition. though i have abt 70 gb of free space. the only other partition is "recovery" one, so i cnt play with it
how shld i perform the installation ?? (4 Replies)
Discussion started by: akshay61286
4 Replies
3. Ubuntu
Hi All
As i m trying to install ubuntu on my virtual PC where h/w confg is as 5GB didk n 512 mb RAm.
after selecting mode option, and after pressing F6 after that screen shows some msg. And not goes to next step.
What is the problem n wht i shall do??
Please provide me solution (3 Replies)
Discussion started by: sunray
3 Replies
4. Ubuntu
Hi all,
I have Windows XP dual boot with Ubuntu 8.10 on my system. I brought in a portable HDD on which I installed Ubuntu 10.04 32-bit. The grub boot loader was installed along with this and to boot windows, I've had to plug in the HDD (with lucid install) everytime. It had been working fine.... (0 Replies)
Discussion started by: morningSunshine
0 Replies
5. Ubuntu
Hi all- I'm getting ready to install Ubuntu onto my Sony Vaio laptop and had a few questions for which I have not yet found the answer.
1)Should I partition my hdd myself (including a swap partition) in Windows or should I do this when installing Ubuntu? When I do partition, since I have over... (2 Replies)
Discussion started by: Gatsby
2 Replies
6. Ubuntu
I wish to install the latest ubuntu on my desktop. How do I go about doing this ?
Also how do I create the superuser or admin once the installation is done ? (3 Replies)
Discussion started by: sundaresh
3 Replies
7. Solaris
System Model and Spec
Sun Enterprise 420R
Processor Speed: 450 MHz (4 processors)
Installed RAM: 4 GB
Os: Solaris 8 Sparc
I successfully installed standard oracle 8i setup on our database server specs above but after installation was competed and it went to creating database I got the... (2 Replies)
Discussion started by: Wpgn
2 Replies
8. Ubuntu
I've done a whole days work of researching how to install a program on ubuntu.. so first I downloaded python.. unpackaged it from .tar.xz now its just python-3.4.2 then I navigated to the dir in terminal.. then ran the ./configure make make test sudo make install commands which took like 10 minutes... (2 Replies)
Discussion started by: Marniwild
2 Replies
9. Shell Programming and Scripting
Hello everyone,
I've got some problem intalling a perl module.
The installation is well done as you can see below.
gueg@ux31:~$ sudo apt-get install libwww-mechanize-perl
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances
Lecture des informations d'état...... (4 Replies)
Discussion started by: tot94
4 Replies
FREE(1) User Commands FREE(1)
NAME
free - Display amount of free and used memory in the system
SYNOPSIS
free [options]
DESCRIPTION
free displays the total amount of free and used physical and swap memory in the system, as well as the buffers and caches used by the ker-
nel. The information is gathered by parsing /proc/meminfo. The displayed columns are:
total Total installed memory (MemTotal and SwapTotal in /proc/meminfo)
used Used memory (calculated as total - free)
free Unused memory (MemFree and SwapFree in /proc/meminfo)
shared Memory used (mostly) by tmpfs (Shmem in /proc/meminfo, available on kernels 2.6.32, displayed as zero if not available)
buffers
Memory used by kernel buffers (Buffers in /proc/meminfo)
cached Memory used by the page cache (calculated as Cached - Shmem in /proc/meminfo - the Cached value is actually the sum of page cache
and tmpfs memory)
OPTIONS
-b, --bytes
Display the amount of memory in bytes.
-k, --kilo
Display the amount of memory in kilobytes. This is the default.
-m, --mega
Display the amount of memory in megabytes.
-g, --giga
Display the amount of memory in gigabytes.
--tera Display the amount of memory in terabytes.
-h, --human
Show all output fields automatically scaled to shortest three digit unit and display the units of print out. Following units are
used.
B = bytes
K = kilos
M = megas
G = gigas
T = teras
If unit is missing, and you have petabyte of RAM or swap, the number is in terabytes and columns might not be aligned with header.
-c, --count count
Display the result count times. Requires the -s option.
-l, --lohi
Show detailed low and high memory statistics.
-o, --old
Display the output in old format, the only difference being this option will disable the display of the "buffer adjusted" line.
-s, --seconds seconds
Continuously display the result delay seconds apart. You may actually specify any floating point number for delay, usleep(3) is
used for microsecond resolution delay times.
--si Use power of 1000 not 1024.
-t, --total
Display a line showing the column totals.
--help Print help.
-V, --version
Display version information.
FILES
/proc/meminfo
memory information
SEE ALSO
ps(1), slabtop(1), top(1), vmstat(8).
AUTHORS
Written by Brian Edmonds.
REPORTING BUGS
Please send bug reports to <procps@freelists.org>
procps-ng September 2011 FREE(1)