I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
So I am not able to boot.
I found it very strange to have these errors because, all I had was a power failure to the blade, and I have managed to power on successfully the other blade on the same chassis
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Hello all,
Let me introduce about the context and my environment.
We have an AIX 6.1 system, it has 4 FC channels
/ > lsdev -Cc adapter | grep fcs
fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 23-T1... (14 Replies)
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
LEARN ABOUT NETBSD
eap
EAP(4) BSD Kernel Interfaces Manual EAP(4)NAME
eap -- AudioPCI audio device driver
SYNOPSIS
eap* at pci? dev ? function ?
audio* at audiobus?
joy* at eap?
midi* at eap?
options EAP_USE_BOTH_DACS
DESCRIPTION
The eap driver provides support for the Ensoniq AudioPCI and Creative Labs SoundBlaster PCI series of audio cards. All models based on the
ES1370, ES1371, and ES1373 chips are supported.
By specifying:
options EAP_USE_BOTH_DACS
a second audio device is attached. You can use it simply by directing audio output to it. This way it is possible for two different pro-
grams to use the "same" audio device simultaneously.
SEE ALSO ac97(4), audio(4), joy(4), midi(4), pci(4)HISTORY
The eap device driver appeared in NetBSD 1.4.
CAVEATS
The joystick port hardware works by emulating a legacy isa(4) joystick port, bypassing the pci(4) bus method for address allocation. This is
unlikely to work on PCI busses other than the primary one. There is also a possibility for conflicts with real ISA devices because the PCI
bus is probed before ISA. Use with caution.
BSD July 22, 2006 BSD