06-19-2018
Do you have support for the M5000? I would say replacing the faulted part should be enough. You can also try to reset the fault and try again to powerup the system. But go slowly with a poweron -d 0 first and see what happens. If domain 0 is running, you can try to start domain 1.
This User Gave Thanks to DukeNuke2 For This Post:
9 More Discussions You Might Find Interesting
1. AIX
Hello:
NOOB here. I attempted to use smit mkcd. Failed on first attempt, not enough space. 2nd attempt tried to place iso on /usr, not enough space there. Cleanup ran for about 5 minutes after aborting. Now AIX won't boot. LCD display on 7029-6E3 says: 0517 MOUNT /USR. Attempted to boot from CD... (11 Replies)
Discussion started by: bbird
11 Replies
2. Solaris
Hi,
I 've a fully loaded M5000 which i would like to partition in 4 domains but i have a concern that since we have only 4 internal disks how can we partition the box in for domains with 2 disks ( mirrored ) in each domain. Should i go ahead with 1 Lun from SAN and 1 internal disk for each of 4... (3 Replies)
Discussion started by: fugitive
3 Replies
3. Solaris
Hi i 've a M5000 running 2 domains in my Lab with following hardconf
SPARC Enterprise M5000; Memory_Size:128 GB;
+-----------------------------------+------------+
| FRU | Quantity |
+-----------------------------------+------------+
| MBU_B... (3 Replies)
Discussion started by: fugitive
3 Replies
4. Solaris
Please advise. Thank you
bash-3.00# cd /usr/sunvts/bin/
bash-3.00# ls
bios.bin iobushangscript.sh stopsunvts vtsprobe
cmos.bin javabridge.jar sunlink vtsreportgenerate
dispatcher loadVtsServer svmVolDiskList vtstalk
env6test... (6 Replies)
Discussion started by: incredible
6 Replies
5. Hardware
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Discussion started by: desertdenizen
2 Replies
6. IP Networking
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
7. Solaris
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
Discussion started by: goya
3 Replies
8. AIX
A team member installed the wrong version of License Code on a Power 740 system used in our Development environment.
The system will no longer boot.
Does anyone have IBM documentation or experience to share on recovering a system that currently reports "Unsupported License Code version... (1 Reply)
Discussion started by: kevinedailey
1 Replies
9. UNIX for Beginners Questions & Answers
Can anyone offer any advice on how to modify the script below to work on a new system we have, that has no graphics capability? We admin the system through a serial RAS device. I've tried running the below script through the RAS and through an ssh -X session. It failed with something like "GTK... (3 Replies)
Discussion started by: yelirt5
3 Replies
LEARN ABOUT V7
asadmin-start-domain
asadmin-start-domain(1AS) User Commands asadmin-start-domain(1AS)
NAME
asadmin-start-domain, start-domain - starts the given domain
SYNOPSIS
start-domain [--domaindir install_dir/domains] [--terse=false] [--echo=false] [--verbose=false] [--debug] [domain_name]
start-domain starts the specified domain. If there is only one domain in the default domain directory (install_dir/domains), then no oper-
and is required to start the domain. However, if there is more than one domain, the domain operand must be specified. This command can only
be run locally.
OPTIONS
--domaindir directory where the domain is to be started. If specified, path must be accessible in the filesystem. If not speci-
fied, the domain is started in the default install_dir/domains directory.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script. Default is false.
--echo setting to true will echo the command line statement on the standard output. Default is false.
--verbose by default this flag is set to false. If set to true, detailed server startup output is displayed. Press CTRL-C to
kill the server. Press CTRL- to print a thread dump.
--debug by default this flag is set to false. If set to true, the server is started in debug mode and prints the JPDA port
on the console.
OPERANDS
domain_name name of the domain. Must be a unique name.
Example 1: Using start-domain
asadmin> start-domain sampleDomain
Starting Domain sampleDomain, please wait.
Domain sampleDomain started
Where: the sampleDomain domain is started.
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-domain(1AS), asadmin-delete-domain(1AS), asadmin-stop-domain(1AS), asadmin-list-domains(1AS)
J2EE 1.4 SDK March 2004 asadmin-start-domain(1AS)