|
|
Sponsored Content
Operating Systems
SCO
Installation on SCO Openserver 5.0.5
Post 303017399 by crt001 on Tuesday 15th of May 2018 10:16:05 AM
05-15-2018
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
LEARN ABOUT NETBSD
mpt
MPT(4) BSD Kernel Interfaces Manual MPT(4) NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver SYNOPSIS
mpt* at pci? dev ? function ? scsibus* at mpt? DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI and Fibre Channel and SAS controllers: o 53c1020 (Ultra320 SCSI) o 53c1030 (Dual Ultra320 SCSI) o AS1068 (SAS/SATA) o FC909 (1Gb/s Fibre Channel) o FC909A (Dual 1Gb/s Fibre Channel) o FC919 (2Gb/s Fibre Channel) o FC919X (2Gb/s Fibre Channel, PCI-X) o FC929 (Dual 2Gb/s Fibre Channel) o FC929X (Dual 2Gb/s Fibre Channel, PCI-X) SEE ALSO
cd(4), ch(4), intro(4), pci(4), scsi(4), sd(4), siop(4), st(4), uk(4) HISTORY
The mpt driver first appeared in NetBSD 2.0. AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley . It was ported to NetBSD by Jason R. Thorpe and contributed by Wasabi Sys- tems, Inc. BSD
February 16, 2009 BSD