02-19-2018
Very good. Does it show the data/filesystems you are expecting?
If you are certain that they are not is use elsewhere, can you mount them?
If you are not sure, think carefully. Trying to mount them may just refuse, but it may possible say "Are you sure?" and then force it or just try and fails with a suggestion to fsck it. All of these could be very bad for your data. When sharing a LUN/filesystem(s) between servers, there is usually a need for good HA software. There are all sorts of problems, such as the free block list which will be held in memory, so if one side uses some free blocks, the other side doesn't know about it and could just use the same blocks causing data loss.
Kind regards,
Robin
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I have a file --> file1.txt
i need to copy this file to another server using FTP....the 2 servers are server1 and server2..may i know how to write a script that can do this?
thanks in advance! Im a newbie to this... (4 Replies)
Discussion started by: forevercalz
4 Replies
2. Solaris
hi all
can anyone tell me how to track a new attached LUN in a solaris server?? (3 Replies)
Discussion started by: raynu.sharma
3 Replies
3. IP Networking
I just moved a dedicated server, which included moving to a new subnet, and new IP address. Now my server is not reconnecting - I've tried ifconfig, altering the etc/hosts file with the new ip address, with no luck. (5 Replies)
Discussion started by: esmerika
5 Replies
4. Solaris
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Discussion started by: uuontario
4 Replies
5. Red Hat
Hi All,
I am new for this blog and this is my first Query on this blog. I would like to dael with graet masters on linux.
Here we go,
After storage people created the LUN, How to add that LUN to Linux server. (Make that LUN visibility on linux server.) ?
How to view the LUN... (5 Replies)
Discussion started by: abhay1983
5 Replies
6. AIX
Hi,
I have compiled FreeTDS on AIX 5.3. Its my dev environment so I have c compilers on the box so I was able to compile. From the test environment onwards I will not be able to have c compilers. I tried to move these files directly to the test environment with the same directory structure but I... (2 Replies)
Discussion started by: vijayraghavk
2 Replies
7. Red Hat
Hi,
I am trying to setup multipathing (using DM multipath) for a redhat cluster setup ...all setup is done but issue is :
node 1 shows the shared iscsi lun as sdc
node 2 shows the same as sdg (changes on reboots)
Due to this (i guess) i get i/o error & i can not read files created by... (0 Replies)
Discussion started by: heman96
0 Replies
8. Linux
I have created a lun on Storage and connected it to server using fiber channel.
LUN is presented on new Server .
How do i check and mount this newly created LUN? (1 Reply)
Discussion started by: pinga123
1 Replies
9. Post Here to Contact Site Administrators and Moderators
ssssssssssss (0 Replies)
Discussion started by: sampathenjoy
0 Replies
LEARN ABOUT NETBSD
badsect
BADSECT(8) BSD System Manager's Manual BADSECT(8)
NAME
badsect -- create files to contain bad sectors
SYNOPSIS
badsect bbdir sector ...
DESCRIPTION
badsect makes a file to contain a bad sector. Normally, bad sectors are made inaccessible by the standard formatter, which provides a for-
warding table for bad sectors to the driver; see bad144(8) for details. If a driver supports the bad blocking standard it is much preferable
to use that method to isolate bad blocks, since the bad block forwarding makes the pack appear perfect, and such packs can then be copied
with dd(1). The technique used by this program is also less general than bad block forwarding, as badsect can't make amends for bad blocks
in the i-list of file systems or in swap areas.
On some disks, adding a sector which is suddenly bad to the bad sector table currently requires the running of the standard DEC formatter.
Thus to deal with a newly bad block or on disks where the drivers do not support the bad-blocking standard badsect may be used to good
effect.
badsect is used on a quiet file system in the following way: First mount the file system, and change to its root directory. Make a directory
BAD there. Run badsect giving as argument the BAD directory followed by all the bad sectors you wish to add. The sector numbers must be
relative to the beginning of the file system, but this is not hard as the system reports relative sector numbers in its console error mes-
sages. Then change back to the root directory, unmount the file system and run fsck(8) on the file system. The bad sectors should show up
in two files or in the bad sector files and the free list. Have fsck(8) remove files containing the offending bad sectors, but do not have
it remove the BAD/nnnnn files. This will leave the bad sectors in only the BAD files.
badsect works by giving the specified sector numbers in a mknod(2) system call, creating an illegal file whose first block address is the
block containing bad sector and whose name is the bad sector number. When it is discovered by fsck(8) it will ask ``HOLD BAD BLOCK ?'' A
positive response will cause fsck(8) to convert the inode to a regular file containing the bad block.
DIAGNOSTICS
badsect refuses to attach a block that resides in a critical area or is out of range of the file system. A warning is issued if the block is
already in use.
SEE ALSO
bad144(8), fsck(8)
HISTORY
The badsect command appeared in 4.1BSD.
BUGS
If more than one of the sectors in a file system fragment are bad, you should specify only one of them to badsect, as the blocks in the bad
sector files actually cover all the sectors in a file system fragment.
BSD
June 5, 1993 BSD