Sponsored Content
Full Discussion: FileSystems under HACMP
Operating Systems AIX FileSystems under HACMP Post 303007221 by LoLo92 on Tuesday 14th of November 2017 05:00:20 AM
Old 11-14-2017
FileSystems under HACMP

Dear Fellows,

I'm now working under a HACMP Cluster (version 7.1) with 2 nodes (Node1 active / Node2 passive), and 1 Resource Group on active node (Node1), which is UNMANAGED for boths nodes.
So, all VG Data are on Node1.
Then I had a JFS2 FileSystem full (located on one of these VG Data called "VG_Clust") that I had to increase it with LVM commands (chfs), not CSPOC ones (cl_chfs) and this worked fine.

This "VG_Clust" is in "read/write" permission, "Enhanced-Capable" and VG Mode "Concurrent" .

In case of Failover to Node2, should I need to "Verify and Synchronize HACMP" or perform Script Failure from Node1 ?

For so, this requires HACMP to be down ?

Could you confirm if these steps below is correct ?
smitty hacmp -> Custom Cluster Configuration -> Verify and Synchronize Cluster Configuration (Advanced)

Thanks for your kind reply.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Filesystems

my partner change the server's ip address and now i can't to mount the oracle's filesystem, what i do? i don't want to reinstall Unix. My unix is SCO UNIX 5.0.5 (9 Replies)
Discussion started by: marun
9 Replies

2. Shell Programming and Scripting

Filesystems GT 95%

Hi How can I only print the file systems that are more than 95% full. I used the df -k output and tried to check for each file system and then print only the ones that meet the criteria... But my solution seems cloodgie ... (3 Replies)
Discussion started by: YS2002
3 Replies

3. Filesystems, Disks and Memory

Vdump of two filesystems

Dear Experts, Is it possible to take a backup of two file systems using a single vdump command? Thanks Wilson (4 Replies)
Discussion started by: geraldwilson
4 Replies

4. UNIX for Advanced & Expert Users

resize filesystems

Dear All We have HP9000 rp7400 Server running with hp-ux 11i. Our Disk storage has two volume groups and are allocated as follows: 1. /#vgdisplay -v --- Volume groups --- VG Name /dev/vg00 VG Write Access read/write VG Status available... (1 Reply)
Discussion started by: mhbd
1 Replies

5. AIX

HACMP and Filesystems question

Hello all. Yes, I searched the forum first :) I have hacmp running on 2 nodes. I wish to add a filesystem to the primary node to and existing shared VG. Not sure how to do this in a cluster environment. My scenario: Create the fs in the hacmp screens in smit add in the fs to and... (1 Reply)
Discussion started by: mhenryj
1 Replies

6. UNIX for Dummies Questions & Answers

mounted filesystems

how to check the record of previously mounted remote filesystems after the filesystems are unmounted .operating system is solaris 10 (0 Replies)
Discussion started by: ravijanjanam12
0 Replies

7. AIX

HACMP does not start db2 after failover (db2nodes not getting modified by hacmp)

hi, when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies

8. Shell Programming and Scripting

Filesystems using more than 75% capacity

i need to write a shell script for printing the list of filesystems whose disk utilization is more than 75%...i tried using df -h along with awk but cud'nt make the combination work.....:wall: when we do df -h then the filesystems which are using more than 75% capacity shud be printed according to... (11 Replies)
Discussion started by: xtatic
11 Replies

9. Shell Programming and Scripting

filesystems > 70%

I need a scrip that will show me the filesystems that are greater than 70%...but not sure how to filter using the df -h | grep Thank you for your help!! (6 Replies)
Discussion started by: eponcedeleonc
6 Replies

10. Solaris

Clustering filesystems

SunOS 5.10 Generic_142900-15 sun4u sparc SUNW,SPARC-Enterprise How can I tell if "clustering" is being used in my shop? I have to file systems that are identical. These filesystems are nfs mounted. But how can I tell if they are being kept in sync as a result of clustering or some other... (2 Replies)
Discussion started by: Harleyrci
2 Replies
VOTEQUORUM_QDEVICE_MASTER_WINS(3)		    Corosync Cluster Engine Programmer's Manual 		 VOTEQUORUM_QDEVICE_MASTER_WINS(3)

NAME
votequorum_qdevice_master_wins - Sets or clears quorum device master_wins flag SYNOPSIS
#include <corosync/votequorum.h> int votequorum_qdevice_master_wins(votequorum_handle_t handle const char name, unsigned int allow); DESCRIPTION
The votequorum_qdevice_master_wins informs votequorum whether or not the currently registered qdevice subsystem supports 'master_wins' mode (default 0). This mode allows the qdevice to effectively take over the quorum calculations of votequorum. Any node with an active qdevice that also has master_wins set becomes quorate regardless of the node votes of the cluster. It is left up to the qdevice subsystem itself (not part of votequorum) to communicate across the nodes or otherwise provide some system of deciding which nodes will be part of the quo- rate cluster, if any. eg They may be the set of nodes that has access to a quorum disk. name The name of the currently registered quorum device on this node. This must match the existing name known to votequorum. allow 0 (the default) means that master_wins is not active on this node. 1 means that master_wins is active on this node. RETURN VALUE
This call returns the CS_OK value if successful, otherwise an error is returned. ERRORS
CS_ERR_TRY_AGAIN Resource temporarily unavailable CS_ERR_INVALID_PARAM Invalid argument CS_ERR_ACCESS Permission denied CS_ERR_LIBRARY The connection failed CS_ERR_INTERRUPT System call inturrupted by a signal CS_ERR_NOT_SUPPORTED The requested protocol/functuality not supported CS_ERR_MESSAGE_ERROR Incorrect auth message received CS_ERR_NO_MEMORY Not enough memory to completed the requested task SEE ALSO
votequorum_overview(8), votequorum_initialize(3), votequorum_finalize(3), votequorum_getinfo(3), votequorum_trackstart(3), votequo- rum_trackstop(3), votequorum_fd_get(3), votequorum_dispatch(3), votequorum_context_set(3), votequorum_context_get(3), votequorum_setex- pected(3), votequorum_setvotes(3), votequorum_qdevice_register(3), votequorum_qdevice_poll(3), votequorum_qdevice_update(3), corosync Man Page 2014-06-10 VOTEQUORUM_QDEVICE_MASTER_WINS(3)
All times are GMT -4. The time now is 05:16 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy