deleted data, now 99% free- but same result
do I have to destroy and recreate?
---------- Post updated at 06:29 AM ---------- Previous update was at 05:01 AM ----------
for some reason I can not get it to see the new disk , the new disk slice is 500 gig, but it is still seeing the old one that is 200g. do i have to destroy and re create using the new disk? i just thought replacing would do the trick.
Last edited by Scott; 11-10-2017 at 05:03 PM..
Reason: CODE tags
Actually have a few different issues, wondering if I could get input on (tried reading/searching for an answer, with no luck)
1. Have a v240 running sol9 that needs a bad disk replaced. So, here are the steps I took:
a. detached from mirroring
b. cleared mirroring (metaclear)
c.... (4 Replies)
solaris os run on X86.
bootdisk have been mirrored.but there is one disk miss,I want to replace the fail disk,but after I replace the disk,the system can't boot!
pls help! (2 Replies)
Originally Posted by panos83
Hello there Sir,
according to this old post,
https://www.unix.com/sco/100001-warni...ler-found.html
i try to restore an old image to a new hard disk drive.
The problem is that i don't have basic information such as:
1) Which btld driver do i... (3 Replies)
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
Scenario1:
VG00 lvm,not mirrored,2 disk of 36GB vg size
VG00 size is under 30G.
Is possible to remove a disk of 36GB and replace "on fly"
with a disk of 300GB on VG00?
Thanks (6 Replies)
I added a disk to a zpool using "zpool add diskname"
My intention was mirror a zpool disk that no mirror; that is a zpool with only one disk. I did not issue the right command. Now, the disk has been added successfully but I cannot remove nor detach it as Solaris 11 thinks it has data on it... (14 Replies)
Hello,
I need some help in recovering ZFS pool. Here is scenerio. There are two disks -
c0t0d0 - This is good disk. I cloned it from other server and boot server from this disk.
c0t1d0 - This is original disk of this server, having errors. I am able to mount it on /mnt. So that I can copy... (1 Reply)
Hello,
I see hard and transport errors on all disks under treso pool and looks like some data corruption too. I want to take backup before, I reboot and replace disk. As of now, there are no slots free on server, so one option is, to break mirror, remove second disk (I need two disks, because... (5 Replies)
On an OmniOS server, I removed a single-disk pool I was using for testing.
Now, when I run zpool import it will show it as FAULTED, since that single disk not available anymore.
# zpool import
pool: fido
id: 7452075738474086658
state: FAULTED
status: The pool was last... (11 Replies)
Discussion started by: priyadarshan
11 Replies
LEARN ABOUT NETBSD
svhlabel
SVHLABEL(8) BSD System Manager's Manual SVHLABEL(8)NAME
svhlabel -- update disk label from SGI Volume Header
SYNOPSIS
svhlabel [-fqrw] device
DESCRIPTION
svhlabel is used to update a NetBSD disk label from the Silicon Graphics Volume Header on disks that were previously used on IRIX systems.
svhlabel scans the Volume Header contained in the first blocks of the disk and generates additional partition entries for the disk from the
entries found.
Each Volume Header entry which does not have an equivalent partition in the disk label (equivalent in having the same size and offset) is
added to the first free partition slot in the disk label. A free partition slot is defined as one with an fstype of 'unused' and a size of
zero ('0'). If there are not enough free slots in the disk label, a warning will be issued.
The raw partition (typically partition c, but d on i386 and some other platforms) is left alone during this process.
By default, the proposed changed disk label will be displayed and no disk label update will occur.
Available options:
-f Force an update, even if there has been no change.
-q Performs operations in a quiet fashion.
-r In conjunction with -w, also update the on-disk label. You probably do not want to do this.
-w Update the in-core label if it has been changed.
SEE ALSO disklabel(8), dkctl(8), mount_efs(8), sgivol(8)HISTORY
The svhlabel command appeared in NetBSD 5.0.
BSD February 26, 2007 BSD