|
|
Sponsored Content
Operating Systems
AIX
Lost Ethernet
Post 303004655 by bakunin on Thursday 5th of October 2017 10:26:21 PM
10-05-2017
|
|
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Discussion started by: at_renai2001
5 Replies
2. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
3. Filesystems, Disks and Memory
First time so excuse my ignorance please.
I may not be accurately describing the issue.
I have inherited a small lab mostly SUN V120s.
We lost power and are trying to recover.
Nope no backups...
The primary issue I have is 1 box is an Oracle Server.
It has 2 36Gb harddrives.
I am able to... (3 Replies)
Discussion started by: murphsr
3 Replies
4. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
5. AIX
Hello everyone
I have a problem with one server, has Aix 5.3 in the errpt has this message
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE
EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN
F3931284 ... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
6. Solaris
I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
Discussion started by: StarSol
4 Replies
7. Solaris
my solris box network is unreachable how to solve this
ipaddress assiagning and entry in vi /etc/host
how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. UNIX for Advanced & Expert Users
Hi,
I have posted several times regarding my application.
In a nutshell, I have a server application that logs attached instrument data over USB and Ethernet. My restriction here is having two wires or more to plug all instrumentation in - at least one for USB and at least one for ethernet.
... (16 Replies)
Discussion started by: fedora18
16 Replies
LEARN ABOUT OSF1
sys_attrs_isa
sys_attrs_isa(5) File Formats Manual sys_attrs_isa(5) NAME
sys_attrs_isa - isa subsystem attributes DESCRIPTION
This reference page lists and describes attributes for the ISA Bus (isa) kernel subsystem. Refer to the sys_attrs(5) reference page for an introduction to the topic of kernel subsystem attributes. For this subsytem, users should modify only the following attribute and do so only for the purpose described. Any other visible attributes cannot or should not be modified. Enables (1) or disables (0) console messages that are used by driver developers to collect information about a configuration prob- lem. A developer can set this attribute by using the sysconfig or sysconfigdb utility. See sysconfig(8), sysconfigdb(8), and cfg- mgr(8) for more information on options for modifying attributes and reconfiguring a kernel subsystem. Default value: 0 SEE ALSO
Commands: cfgmgr(8), sysconfig(8), sysconfigdb(8) Files: stanza(4), cfgmgr.auth(4), sysconfigtab(4) Others: sys_attrs(5) Writing EISA and ISA Bus Device Drivers sys_attrs_isa(5)