Hi,
I'm trying to write a shell script that has a menu and then dependant on the selection, will automate some samba file transfer.
The problem is when I run the code without the case statement it runs fine. but when I put the case statement in the only way I can get the code to run is to... (6 Replies)
Hi All,
this small script is written to recognize user input character.. it is in small case .. upeer case or is a number... but when i input first capital letter say A.. it always gives small character.... what is the problem.
#!/bin/bash
echo "Enter the character"
read a
case $a in
)... (2 Replies)
In a case statement like below :
case $rental in
"car") echo "For $rental Rs.20 per k/m";;
"van") echo "For $rental Rs.10 per k/m";;
"jeep") echo "For $rental Rs.5 per k/m";;
"bicycle") echo "For $rental 20 paisa per k/m";;
*) echo "Sorry, I can not gat a $rental for you";;... (4 Replies)
Hi,
I have a script like below :
#!/bin/ksh
echo "Do you want to export all docs ?"
read alld
echo "Do you want to export template or report only "
read temr
case && ]
#arguments
;;
case && ]
#arguments
;;
case && ]
#arguments
;; (4 Replies)
I'm in the process of writng a function that consists of a case statement is there a way of calling the function and passing a value to it?
ie
function1 () {
case
opt1 do .....
opt2 do.....
esac
}
function opt1
I'm aware the syntax is not correct, but you get the general idea. (1 Reply)
hi all
i am trying to get help with writing a script using case statement to display menu as
1) Authentication log
2) System log
3) Messages
4) Dmesg
5) Boot log
Q) Exit
When selecting the menu by 1 or 2 or 3 o 4 or 5, it should display the last 10 lines of the log files,
if... (3 Replies)
have written the below code to check whether the string received from user is a file name or dir using case statement, but its going into default case*).
#!/bin/sh
#Get a string from user and check whether its a existing filename or not
rm str2
rm str3
echo "enter a file \c"
read fil... (8 Replies)
Hi Gurus,
I have a very weird requirement and have no clue to resolve the issue. please help me get out this difficulty
below two tables, table1 contains the column name. D means this column used for the rule. for example: rule 0 is all columns have value, rule1 is col3 and col7 have no value.... (2 Replies)
Use and complete the template provided. The entire template must be completed. If you don't, your post may be deleted!
1. The problem statement, all variables and given/known data:
This is what is asked:
If the user enters ‘3’, prompt the user for two file names. Verify that the file names... (2 Replies)
Discussion started by: cindy01
2 Replies
LEARN ABOUT CENTOS
pppoe-connect
PPPOE-CONNECT(8) System Manager's Manual PPPOE-CONNECT(8)NAME
pppoe-connect - Shell script to manage a PPPoE link
SYNOPSIS
pppoe-connect [config_file]
pppoe-connect interface user [config_file]
DESCRIPTION
pppoe-connect is a shell script which manages a PPPoE connection using the Roaring Penguin user-space PPPoE client. If you omit con-
fig_file, the default file /etc/sysconfig/network-scripts/ifcfg-ppp0 is used. If you supply interface and user, then they override the
Ethernet interface and user-name settings in the configuration file.
Note that normally, you should not invoke pppoe-connect directly. Instead, use pppoe-start to bring up the PPPoE connection.
pppoe-connect first reads a configuration file. It then brings up a PPPoE connection. If the connection ever drops, a message is logged
to syslog, and pppoe-connect re-establishes the connection. In addition, each time the connection is dropped or cannot be established,
pppoe-connect executes the script /etc/ppp/pppoe-lost if it exists and is executable.
The shell script pppoe-stop causes pppoe-connect to break out of its loop, bring the connection down, and exit.
TECHNICAL DETAILS
pppoe-connect uses the following shell variables from the configuration file:
ETH The Ethernet interface connected to the DSL modem (for example, eth0).
USER The PPPoE user-id (for example, b1xxnxnx@sympatico.ca).
PIDFILE
A file in which to write the process-ID of the pppoe-connect process (for example, /var/run/pppoe.pid). Two additional files ($PID-
FILE.pppd and $PIDFILE.pppoe) hold the process-ID's of the pppd and pppoe processes, respectively.
By using different configuration files with different PIDFILE settings, you can manage multiple PPPoE connections. Just specify the con-
figuration file as an argument to pppoe-start and pppoe-stop.
AUTHOR
pppoe-connect was written by David F. Skoll <dfs@roaringpenguin.com>.
The pppoe home page is http://www.roaringpenguin.com/pppoe/.
SEE ALSO pppoe(8), pppoe-start(8), pppoe-stop(8), pppd(8), pppoe.conf(5), pppoe-setup(8), pppoe-status(8), pppoe-sniff(8), pppoe-server(8), pppoe-
relay(8)4th Berkeley Distribution 21 February 2000 PPPOE-CONNECT(8)