I've just completed a fresh install of HP-UX 11.0 on my 712/80 and everything starts up fine until it gets to the point where X kicks off and I believe at this point is supposed to launch into the CDE login.
It just sits there on the blank X screen with the X cursor for a minute or so then BEEPS... (9 Replies)
I modified the partitions on my Solaris 10 disk using format command in "boot cdrom -s" mode and then tried rebooting with "reboot". It said "Boot load failed".
Why does this happen?
I have faced this error before:( and I went in for a fresh installation of the OS.Can anyone tell me the reason as... (1 Reply)
I've installed AIX 5.1 on a 43p-140, but am unable to log in. At no point in the install did it ask me for a root password. When it boots to the console prompt, I enter "root" as a username, and then after 1 second it cycles right back to another root prompt.
I am accessing the 43p-140... (4 Replies)
Hello,
For whatever reason, after installing Solaris 10 I can ping anything within my own LAN, including the router which is also set as the default gateway, but I have no internet connectivity with it. At first I thought this was a DNS issue, but I can't connect with external IP addresses... (3 Replies)
Hi all
Im rebuilding an 6800 domain with solaris 10. Server is located in a different town and cant be bothered to drive down and install a dvd into its drive.
So, apart from jumpstarting it and using a local DVD, is there a way I can an ISO image to build a new client ?? eg. mount an ISO... (2 Replies)
Good evening all,I'm new to your site, so please bear any infringements or transgressions on my part.I'm new to the whole Solaris boot install over the net scenario, but here's where I'm stuck:I have an M5000 with 2 domains (running unimode). Domain 0 is configured and running Solaris 10. Domain 1... (9 Replies)
Installing Solaris 8 for the first time...on a SunBlade 100. I have original Solaris 8 CD's.
About 45 minutes into the installation, the install halts with the following errors:
ERROR: Could not open file /a/etc/vfstab
ERROR: Could not create the file system mount table /etc/vfstab
I... (4 Replies)
Hi Everyone,
I have been struggling for few days with iSCSI and thought I could get some help on the forum...
fresh install of AIX7.1 TL4 on Power 710, The rootvg relies on 3 SAS disks in RAID 0, 32GB Memory
The lpar Profile is using all of the managed system's resources.
I have connected... (11 Replies)
Hello,
I have downloaded and install debian in computer it is blinking cursor what this mean? (6 Replies)
Discussion started by: Riteshkakkar
6 Replies
LEARN ABOUT CENTOS
locale::codes::langext
Locale::Codes::LangExt(3) User Contributed Perl Documentation Locale::Codes::LangExt(3)NAME
Locale::Codes::LangExt - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangExt;
$lext = code2langext('acm'); # $lext gets 'Mesopotamian Arabic'
$code = langext2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langext_codes();
@names = all_langext_names();
DESCRIPTION
The "Locale::Codes::LangExt" module provides access to standard codes used for identifying language extensions, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language extensions. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langext('acm','alpha');
$lext = code2langext('acm',LOCALE_LANGEXT_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from the IANA language registry, such as 'acm' for Mesopotamian Arabic.
This is the default code set.
ROUTINES
code2langext ( CODE [,CODESET] )
langext2code ( NAME [,CODESET] )
langext_code2code ( CODE ,CODESET ,CODESET2 )
all_langext_codes ( [CODESET] )
all_langext_names ( [CODESET] )
Locale::Codes::LangExt::rename_langext ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangExt::add_langext ( CODE ,NAME [,CODESET] )
Locale::Codes::LangExt::delete_langext ( CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_alias ( NAME ,NEW_NAME )
Locale::Codes::LangExt::delete_langext_alias ( NAME )
Locale::Codes::LangExt::rename_langext_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::delete_langext_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.3 2013-02-27 Locale::Codes::LangExt(3)