Hello Guys
I have a flat file with '|~|' delimited
When I use to record count using below command
awk -FS"+" ' {print $colno}' filename | wc -l
the count is fine
But when I am trying to find the unique number of record the o/p is always 1
awk -FS"+" ' {print $colno}'... (11 Replies)
Hi all I have a need of searching some pattern in file by month and then count unique records
D11
G11
R11 -------> Pattern available in file
S11
Jan$1 to $5 column contains some records in which I want to find unique
for this purpose I have written script like below
awk '/Jan/ ||... (4 Replies)
Hi, I have tab-deliminated data similar to the following:
dot is-big 2
dot is-round 3
dot is-gray 4
cat is-big 3
hot in-summer 5
I want to count the frequency of each individual "unique" value in the 1st column. Thus, the desired output would be as follows:
dot 3
cat 1
hot 1
is... (5 Replies)
Im looking for an awk script that will take the unique values in column 5, then print and count the unique values in column 6.
CA001011500 11111 11111 -9999 201301 AAA
CA001012040 11111 11111 -9999 201301 AAA
CA001012573 11111 11111 -9999 201301 BBB
CA001012710 11111 11111 -9999 201301... (4 Replies)
When I use the below awk to count the unique lines in $4 for the input it seems to work. The answer is 3 because $4 is only unique 3 times in all the entries. However, when I use the same on actual data I get 56,536 and I know the answer should be 56,548. My question is there a better way to... (8 Replies)
Hello Team,
I need your help on the following:
My input file a.txt is as below:
3330690|373846|108471
3330690|373846|108471
0640829|459725|100001
0640829|459725|100001
3330690|373847|108471
Here row 1 and row 2 of column 1 are identical but corresponding column 2 value are... (4 Replies)
Hello experts,
I am converting a number into its binary output as :
read n
echo "obase=2;$n" | bc
I wish to count the maximum continuous occurrences of the digit 1.
Example :
1. The binary equivalent of 5 = 101. Hence the output must be 1.
2. The binary... (3 Replies)
What is an efficient way of counting the number of unique values in a 400 column by 1000 row array and outputting the counts per column, assuming the unique values in the array are:
A, B, C, D
In other words the output should look like: Value COL1 COL2 COL3
A 50 51 52... (16 Replies)
Discussion started by: Geneanalyst
16 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)