Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Bonding IEEE 802.3ad Dynamic link aggregation : Bond showing less than desired throughput
Top Forums UNIX for Advanced & Expert Users Bonding IEEE 802.3ad Dynamic link aggregation : Bond showing less than desired throughput Post 302996603 by MadeInGermany on Thursday 27th of April 2017 04:04:04 PM
Old 04-27-2017
I am not an expert with link aggregation, maybe nobody here is.
It seems there is aggregated eth0 with eth2, and eth1 with eth3.
The only unusual setting is the BOOTPROTO=static for eth0.
You have set xmit_hash_policy=1.
Maybe you should change to xmit_hash_policy=layer3+4, then two hosts can use more interfaces if more services (ports) are involved. But the other way is controlled by the LAN switch.
And - maybe everything works as designed, according to this article.
 

10 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. IP Networking

bonding lacp and link aggregation

Hello, I am trying to get clarity on a few things and am looking for some info. In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth. But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Discussion started by: jaredo
1 Replies

3. IP Networking

Gigabit Link throughput

As a rule of thumb in doing calculations, what figure would you use in Mbytes/sec? I know the answer varies grealty on the topolgy of the network but I wonde what newteok engineers use a rough rule of thumb? Many thanks. (1 Reply)
Discussion started by: debd
1 Replies

4. IP Networking

bonding without switch link aggregation

I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies

5. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

6. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

7. Solaris

Throughput problems with solaris aggregation

Hello gurus, I have the following configuration in the server side: # dladm show-aggr key: 33 (0x0021) policy: L4 address: 0:14:4f:6c:11:8 (auto) device address speed duplex link state nxge0 0:14:4f:6c:11:8 1000 Mbps ... (3 Replies)
Discussion started by: FERCA
3 Replies

8. Solaris

solaris link aggregation problem , once i reboot it is not showing, not able to ping the default gat

Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1 after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies

9. Red Hat

Bonding a Bond with LACP

Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies

10. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

LEARN ABOUT DEBIAN

aoe-discover

aoe-discover(8) 					      System Manager's Manual						   aoe-discover(8)

NAME

       aoe-discover - tell aoe driver to discover AoE devices

SYNOPSIS

       aoe-discover

DESCRIPTION

       The  aoe-discover  command tells the aoe driver to discover ATA over Ethernet (AoE) devices on the network.  All network interfaces will be
       probed with a AoE config query broadcast.

       If the aoe-interfaces command has limited the allowable network interfaces, only devices discovered via allowable  interfaces  will  become
       available.  The default is to make available all AoE devices found on all accessible ethernet networks.

       It's good to run the aoe-discover command after running aoe-interfaces.

EXAMPLE

       In  this  example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic.  After remembering that
       shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then  calls  aoe-discover
       to ask the aoe driver to look for new AoE devices.

	      nai:~# modprobe aoe aoe_iflist="eth0"
	      nai:~# aoe-stat
		 e10.9		  eth0		    up
	      nai:~# aoe-interfaces eth0 eth3
	      nai:~# aoe-discover
	      nai:~# aoe-stat
		  e7.0		  eth3		    up
		  e7.1		  eth3		    up
		  e7.2		  eth3		    up
		  e7.3		  eth3		    up
		  e7.4		  eth3		    up
		  e7.5		  eth3		    up
		  e7.6		  eth3		    up
		  e7.7		  eth3		    up
		  e7.8		  eth3		    up
		  e7.9		  eth3		    up
		 e10.9		  eth0		    up

SEE ALSO

       aoe-interfaces(8), aoe-stat(8), aoetools(8).

AUTHOR

       Ed L. Cashin (ecashin@coraid.com)

																   aoe-discover(8)
All times are GMT -4. The time now is 01:38 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy