04-27-2017
I am not an expert with link aggregation, maybe nobody here is.
It seems there is aggregated eth0 with eth2, and eth1 with eth3.
The only unusual setting is the
BOOTPROTO=static for eth0.
You have set
xmit_hash_policy=1.
Maybe you should change to
xmit_hash_policy=layer3+4, then two hosts can use more interfaces if more services (ports) are involved. But the other way is controlled by the LAN switch.
And - maybe everything works as designed, according to
this article.
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. IP Networking
Hello, I am trying to get clarity on a few things and am looking for some info.
In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth.
But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Discussion started by: jaredo
1 Replies
3. IP Networking
As a rule of thumb in doing calculations, what figure would you use in Mbytes/sec? I know the answer varies grealty on the topolgy of the network but I wonde what newteok engineers use a rough rule of thumb?
Many thanks. (1 Reply)
Discussion started by: debd
1 Replies
4. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
5. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
6. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
7. Solaris
Hello gurus,
I have the following configuration in the server side:
# dladm show-aggr
key: 33 (0x0021) policy: L4 address: 0:14:4f:6c:11:8 (auto)
device address speed duplex link state
nxge0 0:14:4f:6c:11:8 1000 Mbps ... (3 Replies)
Discussion started by: FERCA
3 Replies
8. Solaris
Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1
after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies
9. Red Hat
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies
10. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
LEARN ABOUT PHP
aggregate