04-21-2017
Hi apoklyps3
*
we have needed some inputs/outputs - could you write what you did ( commands and outputs ) ?
where did you extract to unpack the firmware ? ( external stroage ? )
can you see the images/files as separately ( bootloader/kernel/rootfs and the others.. )
- do you have the orginal firmware image outside the flash ?
*
i can try search your hardware but i cannot find any usefull infos.
so i have to learn this :- your device chip details
- your flash chip details
- cat /proc/mounts ( and fstab ? )
- cat /proc/mtd
- have you any tools ? ( flash_erase / nandwrite ... )
( can you list the your binaries related flash that you have .. )
- what is your boot-loader ? any screen output releated booting ?
- can you execute the boot-loader commands ( so is there any prompt ? )
- can you paste the dmesg or /var/log/messages files ?
- did you try the plug in the usb drive and kernel see it ? ( like /dev/sdaX )
- are there any kernel configs ( /proc/configXX , /boot/config* )
3 More Discussions You Might Find Interesting
1. IP Networking
I am trying to set up a linux box as a router, but I am a little confused
on how to do this. I am using Red Hat 9.0 on a machine that has 2
nic cards. Also, I am using a DSL pppoe connection. I have installed
rp-pppoe and I am connected to the internet via the pseudo pppoe
interface. I have... (1 Reply)
Discussion started by: cstovall
1 Replies
2. Cybersecurity
HI all,
I have setup IPTables firewall/Router and my home network, with address space 192.168.10.XXX
Form my private network hosts, i can ping the gateway ( 192.168.10.101 ) , but the reverse is not happening.
Can someone help me as of what i need to do, so that i can ping my private... (1 Reply)
Discussion started by: chandan_m
1 Replies
3. Shell Programming and Scripting
Hey all. Sometimes I'm tasked to change some router configs for the entire network (over 3,000 Cisco routers). Most of the time its a global config parameter so its done with a loop and an IP list as its the same configuration change for all routers. This is working OK.
However, sometimes an... (3 Replies)
Discussion started by: mrkz1974
3 Replies
pxfw(8) pxfw 0.5 pxfw(8)
NAME
pxfw - Firmware flashing tool for Plextor CD/DVD devices
SYNOPSIS
pxfw -l
pxfw -d DEVICE [-if firmware.bin] [-u] [-f] [-v]
pxfw -d DEVICE [-e] [-r] [-t] [-v]
DESCRIPTION
pxfw is the linux firmware flasher for Plextor CD and DVD drives. Remove any disks before flashing.
FEATURES
You can flash the firmware of these drives:
Plextor Premium, Premium-2, PX-712, PX-716, PX-755 and PX-760.
DEVICE
can be an IDE, SCSI, SATA, USB or FireWire connected optical drive. Not all SATA controller support all Plextor features.
Linux:
/dev/hdX: IDE device
/dev/scdX: Linux 2.4: SATA, SCSI, USB device, or IDE device via ide-scsi emulation
/dev/srX: Linux 2.6: IDE device via new ATA layer, SCSI or USB device
OpenBSD/NetBSD:
/dev/rcdX
FreeBSD:
/dev/cd: SCSI device
/dev/acd: ATA device
MacOS X:
/dev/disk:
win32:
C:,D:,E:, ... X:,Y:,Z:
OPTIONS
-l scan busses for all available CD and DVD devices
-if select inputfile. Specify the firmware binary file, which should
be written to DEVICE.
-u proceed update. When the firmware checksum test has succeeded,
write firmware to DEVICE.
-f force flashing. Even if DEVICE is not recognized, or firmware.
checksum has failed, firmware writing will be forced.
Handle with care.
-e read EEPROM from DEVICE.
-r reboot the device.
-t test which opcodes are supported by the device.
-v debug.
EXAMPLES
pxfw -d /dev/hdc -if 755_1.07.bin -u
writes firmware file 755_1.07.bin into Master Drive on Secondary IDE-Port.
pxfw -d /dev/sr3 -e -oe file.foo
reades EEPROM from device /dev/sr3 and writes it to file.foo.
please report man page improvements to T.Maguin@web.de
Gennady ShultZ Kozlov 02 April, 2009 pxfw(8)